Ultrafuse PP @MK4S 0.6

Forward AM · PP · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

→

→

Ultrafuse PP @MK4S 0.6

Includes (3)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: PP inherited
Vendor: Forward AM inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.91 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 60 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 4 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	80 inherited	70 inherited

Other settings

bridge fan speed: 100 inherited
compatible printers condition: printer_model=~/(MK4S|MK4SMMU3|MK3.9S|MK3.9SMMU3)/ and nozzle_diameter[0]==0.6 and ! single_extruder_multi_material via *PP06PG4S*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PPPG*
cooling slowdown logic: consistent_surface via *PPPG*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #F0F0F0 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament deretract speed: 20 via *PP06PG*
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: Material Description Ultrafuse PP is high-performance thermoplastic with low density, high elasticity and high resistance to fatigue. The mechanical properties make it an ideal material for 3D-printing applications which have to endure high stress or strain. The filament has high chemical resistance and a high isolation value. PP is one of the most used materials in the world, due to its versatility and ability to engineer lightweight tough parts. Printing Recommendations: Apply PP tape or Magigoo PP adhesive to the buildplate for optimal adhesion. inherited
filament ramming parameters: 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 2 via *PP06PG*
filament retract layer change: 0 via *PP06PG*
filament retract speed: 60 via *PP06PG*
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament travel max lift: 0.6 via *PP06PG*
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil inherited
full fan speed layer: 3 inherited
idle temperature: 70 via *PP06PG*
start filament gcode: M900 K0 ; Filament gcode M142 S36 ; set heatbreak target temp via *PP06PG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    "Material Description\nUltrafuse PP is high-performance thermoplastic with low density, high elasticity and high resistance to fatigue. The mechanical properties make it an ideal material for 3D-printing applications which have to endure high stress or strain. The filament has high chemical resistance and a high isolation value. PP is one of the most used materials in the world, due to its versatility and ability to engineer lightweight tough parts.\n\nPrinting Recommendations:\nApply PP tape or Magigoo PP adhesive to the buildplate for optimal adhesion."
  ],
  "filament_colour": [
    "#F0F0F0"
  ],
  "filament_vendor": [
    "Forward AM"
  ],
  "filament_density": [
    "0.91"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(MK4S|MK4SMMU3|MK3.9S|MK3.9SMMU3)/ and nozzle_diameter[0]==0.6 and ! single_extruder_multi_material"
  ],
  "filament_max_volumetric_speed": [
    "4"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_type": [
    "PP"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "filament_retract_speed": [
    "60"
  ],
  "filament_deretract_speed": [
    "20"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_travel_max_lift": [
    "0.6"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "name": "Ultrafuse PP @MK4S 0.6",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:46