Ultrafuse ABS

Forward AM · ABS · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*ABSC*

→

Ultrafuse ABS

Inherited from this (7)

Settings

Basic information

Material variant: ABS inherited
Vendor: Forward AM overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 255 inherited
Nozzle (other layers) (°C): 255 inherited

Cooling

Fan minimum (%): 10 overridden
was 15 (inherited)
Fan maximum (%): 20 overridden
was 15 (inherited)
Disable fan for first N layers: 3 overridden
was 4 (inherited)
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 11 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 inherited	100 overridden was 110

Other settings

bridge fan speed: 25 inherited
compatible printers condition: printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) inherited
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #FFFFFF overridden
was #FFF2EC (inherited)
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: Material Description ABS is the second most used 3D printing material. It is strong, flexible and has a high heat resistance. ABS is a preferred plastic for engineers and professional applications. ABS can be smoothened with acetone. To make a proper 3D print with ABS you will need a heated print bed. The filament is available in 9 colors. Printing Recommendations: Apply Tape, adhesion spray or glue to a clean build plate to improve adhesion. overridden
was — (inherited)
filament ramming parameters: 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 2 overridden
filament retract layer change: 0 overridden
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: 0 overridden
start filament gcode: {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif} inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    "Material Description\nABS is the second most used 3D printing material. It is strong, flexible and has a high heat resistance. ABS is a preferred plastic for engineers and professional applications. ABS can be smoothened with acetone. To make a proper 3D print with ABS you will need a heated print bed. The filament is available in 9 colors.\n\nPrinting Recommendations:\n\nApply Tape, adhesion spray or glue to a clean build plate to improve adhesion."
  ],
  "filament_colour": [
    "#FFFFFF"
  ],
  "filament_vendor": [
    "Forward AM"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK3.5|MINIIS).*/}\nM900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0\n{endif}\n\n{if printer_notes=~/.*MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif}\n{endif}\n\n{if printer_notes=~/.*MK3.5.*/}\nM572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode\n{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)"
  ],
  "filament_max_volumetric_speed": [
    "11"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_type": [
    "ABS"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "bridge_fan_speed": [
    "25"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "filament_wipe": [
    "0"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "name": "Ultrafuse ABS",
  "type": "filament"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 11:12
v1 created 2026-05-19 11:07