Ultrafuse PP

Forward AM · PP · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*ABSC*

→

Ultrafuse ABS

→

Ultrafuse PP

Inherited from this (5)

Settings

Basic information

Material variant: PP overridden
was ABS (inherited)
Vendor: Forward AM inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.91 overridden
was 1.04 (inherited)

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 10 (inherited)
Fan maximum (%): 100 overridden
was 20 (inherited)
Disable fan for first N layers: 1 overridden
was 3 (inherited)
Full fan if layer below (sec): 60 overridden
was 30 (inherited)
Slow down if layer below (sec): 20 overridden
was 20 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 15 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 2.5 overridden
was 11 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	80 overridden was 100	70 overridden was 100

Other settings

bridge fan speed: 100 overridden
was 25 (inherited)
compatible printers condition: printer_notes!~/.*MINI.*/ and printer_model!="MK2SMM" and printer_notes!~/.*PG.*/ and ! single_extruder_multi_material overridden
was printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) (inherited)
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #F0F0F0 overridden
was #FFFFFF (inherited)
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament deretract speed: 25 overridden
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: Material Description Ultrafuse PP is high-performance thermoplastic with low density, high elasticity and high resistance to fatigue. The mechanical properties make it an ideal material for 3D-printing applications which have to endure high stress or strain. The filament has high chemical resistance and a high isolation value. PP is one of the most used materials in the world, due to its versatility and ability to engineer lightweight tough parts. Printing Recommendations: Apply PP tape or Magigoo PP adhesive to the buildplate for optimal adhesion. overridden
was Material Description ABS is the second most used 3D printing material. It is strong, flexible and has a high heat resistance. ABS is a preferred plastic for engineers and professional applications. ABS can be smoothened with acetone. To make a proper 3D print with ABS you will need a heated print bed. The filament is available in 9 colors. Printing Recommendations: Apply Tape, adhesion spray or glue to a clean build plate to improve adhesion. (inherited)
filament ramming parameters: 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 2 inherited
filament retract layer change: 0 overridden
was 0 (inherited)
filament retract speed: 25 overridden
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil overridden
was 0 (inherited)
full fan speed layer: 3 overridden
start filament gcode: {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif} inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    "Material Description\nUltrafuse PP is high-performance thermoplastic with low density, high elasticity and high resistance to fatigue. The mechanical properties make it an ideal material for 3D-printing applications which have to endure high stress or strain. The filament has high chemical resistance and a high isolation value. PP is one of the most used materials in the world, due to its versatility and ability to engineer lightweight tough parts.\n\nPrinting Recommendations:\nApply PP tape or Magigoo PP adhesive to the buildplate for optimal adhesion."
  ],
  "filament_colour": [
    "#F0F0F0"
  ],
  "filament_vendor": [
    "Forward AM"
  ],
  "filament_density": [
    "0.91"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK3.5|MINIIS).*/}\nM900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0\n{endif}\n\n{if printer_notes=~/.*MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif}\n{endif}\n\n{if printer_notes=~/.*MK3.5.*/}\nM572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode\n{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes!~/.*MINI.*/ and printer_model!=\"MK2SMM\" and printer_notes!~/.*PG.*/ and ! single_extruder_multi_material"
  ],
  "filament_max_volumetric_speed": [
    "2.5"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_type": [
    "PP"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "filament_retract_speed": [
    "25"
  ],
  "filament_deretract_speed": [
    "25"
  ],
  "name": "Ultrafuse PP",
  "type": "filament"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 11:12
v1 created 2026-05-19 11:07