Prusament PC Space Grade @COREONE 0.8

Prusa · PC · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*ABS*

→

Prusament PC Blend

→

*Prusament PC Space Grade*

→

Prusament PC Space Grade @MK4S

→

Prusament PC Space Grade @MK4S 0.8

→

Prusament PC Space Grade @COREONE 0.8

Includes (9)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: PC inherited
Vendor: Prusa Polymers inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.21 inherited
Cost (/kg): 293 inherited

Print temperature

Nozzle (initial layer) (°C): 290 inherited
Nozzle (other layers) (°C): 290 inherited
Chamber (°C): 55 via *PC08PGC1*

Cooling

Fan minimum (%): 15 overridden
was 12 (inherited)
Fan maximum (%): 20 overridden
was 12 (inherited)
Disable fan for first N layers: 4 inherited
Full fan if layer below (sec): 25 overridden
was 15 (inherited)
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.02 inherited
Max volumetric speed (mm³/s): 18 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	120 inherited	120 inherited

Other settings

bridge fan speed: 30 overridden
was 20 (inherited)
chamber minimal temperature: 40 via *PC08PGC1*
compatible printers condition: printer_model=~/(COREONE|COREONEOAK|COREONEL)/ and nozzle_diameter[0]==0.8 and ! single_extruder_multi_material via *PG_NOHF08C1*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PC08PG*
cooling slowdown logic: consistent_surface via *PC08PG*
enable dynamic fan speeds: 1 overridden
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament abrasive: 1 inherited
filament colour: #BBBBBB inherited
filament cooling final speed: 2.5 via *PC08PG*
filament cooling initial speed: 5 via *PC08PG*
filament cooling moves: 3 via *PC08PG*
filament infill max crossing speed: 0 via *PC08PG*
filament infill max speed: 0 via *PC08PG*
filament load time: 10.9 via *PC08PGC1*
filament loading speed: 10 via *PC08PG*
filament loading speed start: 50 via *PC08PG*
filament minimal purge on wipe tower: 35 via *PC08PG*
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *PC08PG*
filament retract length: nil inherited
filament retract lift: nil inherited
filament shrinkage compensation xy: 0% overridden
filament shrinkage compensation z: 0% overridden
filament soluble: 0 inherited
filament spool weight: 278 inherited
filament stamping distance: 45 via *PC08PG*
filament stamping loading speed: 26.5 via *PC08PG*
filament toolchange delay: 0 via *PC08PG*
filament unload time: 8.9 via *PC08PGC1*
filament unloading speed: 60 via *PC08PG*
filament unloading speed start: 60 via *PC08PG*
full fan speed layer: 0 inherited
idle temperature: 150 via *PC08PGC1*
overhang fan speed 0: 25 overridden
start filament gcode: {if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/} M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA {else} M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Pressure advance {endif} M142 S45 ; set heatbreak target temp via *PC08PG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "293"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#BBBBBB"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_density": [
    "1.21"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.9"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.02"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.9"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S45 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(COREONE|COREONEOAK|COREONEL)/ and nozzle_diameter[0]==0.8 and ! single_extruder_multi_material"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "15"
  ],
  "filament_type": [
    "PC"
  ],
  "hot_plate_temp": [
    "120"
  ],
  "bridge_fan_speed": [
    "30"
  ],
  "nozzle_temperature": [
    "290"
  ],
  "chamber_temperature": [
    "55"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "25"
  ],
  "chamber_minimal_temperature": [
    "40"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "hot_plate_temp_initial_layer": [
    "120"
  ],
  "nozzle_temperature_initial_layer": [
    "290"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "filament_spool_weight": [
    "278"
  ],
  "filament_abrasive": [
    "1"
  ],
  "filament_retract_length": [
    "nil"
  ],
  "idle_temperature": [
    "150"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "0"
  ],
  "filament_shrinkage_compensation_z": [
    "0%"
  ],
  "filament_shrinkage_compensation_xy": [
    "0%"
  ],
  "overhang_fan_speed_0": [
    "25"
  ],
  "enable_dynamic_fan_speeds": [
    "1"
  ],
  "name": "Prusament PC Space Grade @COREONE 0.8",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:32