Prusament PC Space Grade

Prusa · PC · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*ABS*

→

Prusament PC Blend

→

*Prusament PC Space Grade*

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*PC*

Inherited from this (3)

Settings

Basic information

Material variant: PC inherited
Vendor: Prusa Polymers inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.21 overridden
was 1.22 (inherited)
Cost (/kg): 293 overridden
was 51.53 (inherited)

Print temperature

Nozzle (initial layer) (°C): 290 overridden
was 275 (inherited)
Nozzle (other layers) (°C): 290 overridden
was 275 (inherited)
Chamber (°C): 55 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 20 inherited
Disable fan for first N layers: 4 overridden
was 4 (inherited)
Full fan if layer below (sec): 15 overridden
was 30 (inherited)
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.02 overridden
was 0.93 (inherited)
Max volumetric speed (mm³/s): 8 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	120 overridden was 110	120 overridden was 115

Other settings

bridge fan speed: 30 inherited
chamber minimal temperature: 40 inherited
compatible printers condition: printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.8 and printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) overridden
was printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]!=0.8 and printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) (inherited)
cooling: 1 inherited
cooling perimeter transition distance: 10 inherited
cooling slowdown logic: consistent_surface inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament abrasive: 1 overridden
filament colour: #BBBBBB overridden
was #DEE0E6 (inherited)
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract length: nil overridden
filament retract lift: nil overridden
was 0.2 (inherited)
filament soluble: 0 inherited
filament spool weight: 278 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
full fan speed layer: 0 inherited
start filament gcode: {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.2{elsif nozzle_diameter[0]==0.8}0.09{elsif nozzle_diameter[0]==0.4}0.35{elsif nozzle_diameter[0]==0.25}0.98{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.6}0.022{elsif nozzle_diameter[0]==0.8}0.016{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.09{else}0{endif} ; Filament gcode {endif} via *PC*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "293"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#BBBBBB"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_density": [
    "1.21"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.02"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK3.5|MINIIS).*/}\nM900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0\n{endif}\n\n{if printer_notes=~/.*MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.2{elsif nozzle_diameter[0]==0.8}0.09{elsif nozzle_diameter[0]==0.4}0.35{elsif nozzle_diameter[0]==0.25}0.98{else}0{endif}\n{endif}\n\n{if printer_notes=~/.*MK3.5.*/}\nM572 S{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.6}0.022{elsif nozzle_diameter[0]==0.8}0.016{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.09{else}0{endif} ; Filament gcode\n{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes!~/.*PRINTER_MODEL_MK(2|2.5).*/ and nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.8 and printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "PC"
  ],
  "hot_plate_temp": [
    "120"
  ],
  "bridge_fan_speed": [
    "30"
  ],
  "nozzle_temperature": [
    "290"
  ],
  "chamber_temperature": [
    "55"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "chamber_minimal_temperature": [
    "40"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "hot_plate_temp_initial_layer": [
    "120"
  ],
  "nozzle_temperature_initial_layer": [
    "290"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "filament_spool_weight": [
    "278"
  ],
  "filament_abrasive": [
    "1"
  ],
  "filament_retract_length": [
    "nil"
  ],
  "name": "*Prusament PC Space Grade*",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:10