Buddy3D PETG @XL HF0.5

Buddy3D · OTHER · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*PET*

→

Prusament PETG

→

Prusament PETG @PG 0.6

→

Prusament PETG @XL HF0.5

→

Buddy3D PETG @XL HF0.5

Includes (3)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: PETG inherited
Vendor: Buddy3D overridden
was Prusa Polymers (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 25.99 overridden
was 29.99 (inherited)

Print temperature

Nozzle (initial layer) (°C): 255 inherited
Nozzle (other layers) (°C): 255 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 60 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 15 inherited
Slow down if layer below (sec): 14 via *PET06PG*
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 24 overridden
was 26 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	80 via include	80 via include

Other settings

bridge fan speed: 60 inherited
compatible printers condition: printer_notes=~/.*XL.*/ and nozzle_diameter[0]==0.5 and printer_notes=~/.*HF_NOZZLE.*/ via *PET05HFXL*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PET06PG*
cooling slowdown logic: consistent_surface via *PET06PG*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #C0C0C0 inherited
filament cooling final speed: 2.5 via *PET06PG*
filament cooling initial speed: 5 via *PET06PG*
filament cooling moves: 3 via *PET06PG*
filament infill max crossing speed: 120 via *PET05HFXL*
filament infill max speed: 200 via *PET05HFXL*
filament load time: 10.5 via *PET06PG*
filament loading speed: 10 via *PET06PG*
filament loading speed start: 50 via *PET06PG*
filament minimal purge on wipe tower: 35 via *PET05HFXL*
filament multitool ramming: 1 via *PET05HFXL*
filament multitool ramming flow: 40 via *PET05HFXL*
filament multitool ramming volume: 10 via *PET05HFXL*
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *PET06PG*
filament retract before wipe: 20 via *PET06PG*
filament retract length: 0.8 via *PET06PG*
filament retract length toolchange: 20 via *PET05HFXL*
filament retract lift: 0.15 via *PET06PG*
filament soluble: 0 inherited
filament spool weight: 278 inherited
filament stamping distance: 45 via *PET06PG*
filament stamping loading speed: 26.5 via *PET06PG*
filament toolchange delay: 0 via *PET06PG*
filament travel max lift: 1.5 via *PET05HFXL*
filament travel ramping lift: 1 via *PET05HFXL*
filament travel slope: 1 via *PET05HFXL*
filament unload time: 8.5 via *PET06PG*
filament unloading speed: 60 via *PET06PG*
filament unloading speed start: 60 via *PET06PG*
filament wipe: 1 via *PET06PG*
idle temperature: 70 via *PET06PG*
start filament gcode: M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.055{elsif nozzle_diameter[filament_extruder_id]==0.5}0.049{elsif nozzle_diameter[filament_extruder_id]==0.6}0.039{elsif nozzle_diameter[filament_extruder_id]==0.8}0.028{elsif nozzle_diameter[filament_extruder_id]==0.25}0.2{elsif nozzle_diameter[filament_extruder_id]==0.3}0.1{else}0{endif} ; Filament gcode M142 S36 ; set heatbreak target temp via *PAHF_BUDDY_PETG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "25.99"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#C0C0C0"
  ],
  "filament_vendor": [
    "Buddy3D"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "14"
  ],
  "start_filament_gcode": [
    "M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.055{elsif nozzle_diameter[filament_extruder_id]==0.5}0.049{elsif nozzle_diameter[filament_extruder_id]==0.6}0.039{elsif nozzle_diameter[filament_extruder_id]==0.8}0.028{elsif nozzle_diameter[filament_extruder_id]==0.25}0.2{elsif nozzle_diameter[filament_extruder_id]==0.3}0.1{else}0{endif} ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*XL.*/ and nozzle_diameter[0]==0.5 and printer_notes=~/.*HF_NOZZLE.*/"
  ],
  "filament_max_volumetric_speed": [
    "24"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "bridge_fan_speed": [
    "60"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "filament_spool_weight": [
    "278"
  ],
  "filament_wipe": [
    "1"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_retract_lift": [
    "0.15"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_retract_length": [
    "0.8"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_infill_max_speed": [
    "200"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_retract_before_wipe": [
    "20"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "120"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_retract_length_toolchange": [
    "20"
  ],
  "name": "Buddy3D PETG @XL HF0.5",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:27