*PET05HFXL*
Unknown · OTHER
· by prusa-system
· 0 downloads
Inheritance
-
*PETXL*
→
*PET05HFXL*
Includes (1)
Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.
Settings
Flow
- Max volumetric speed (mm³/s)
-
24 overridden
Bed temperature
| Plate | Initial layer (°C) | Other layers (°C) |
|---|---|---|
| High Temp Plate |
80
inherited
|
80
inherited
|
Other settings
- compatible printers condition
-
printer_notes=~/.*XL.*/ and nozzle_diameter[0]==0.5 and printer_notes=~/.*HF_NOZZLE.*/ overriddenwas printer_notes=~/.*XL.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and printer_notes!~/.*HF_NOZZLE.*/ (inherited)
- filament infill max crossing speed
-
120 overridden
- filament infill max speed
-
200 overridden
- filament minimal purge on wipe tower
-
35 inherited
- filament multitool ramming
-
1 inherited
- filament multitool ramming flow
-
40 inherited
- filament multitool ramming volume
-
10 inherited
- filament retract length toolchange
-
20 inherited
- filament travel max lift
-
1.5 inherited
- filament travel ramping lift
-
1 inherited
- filament travel slope
-
1 inherited
- start filament gcode
-
M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.047{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.033{elsif nozzle_diameter[filament_extruder_id]==0.8}0.021{elsif nozzle_diameter[filament_extruder_id]==0.25}0.17{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Filament gcode M142 S36 ; set heatbreak target temp via *PA_PETHF*
Raw resolved JSON
{
"hot_plate_temp": [
"80"
],
"filament_travel_slope": [
"1"
],
"filament_travel_max_lift": [
"1.5"
],
"filament_multitool_ramming": [
"1"
],
"filament_travel_ramping_lift": [
"1"
],
"hot_plate_temp_initial_layer": [
"80"
],
"compatible_printers_condition": [
"printer_notes=~/.*XL.*/ and nozzle_diameter[0]==0.5 and printer_notes=~/.*HF_NOZZLE.*/"
],
"filament_multitool_ramming_flow": [
"40"
],
"filament_multitool_ramming_volume": [
"10"
],
"filament_retract_length_toolchange": [
"20"
],
"filament_minimal_purge_on_wipe_tower": [
"35"
],
"start_filament_gcode": [
"M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.047{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.033{elsif nozzle_diameter[filament_extruder_id]==0.8}0.021{elsif nozzle_diameter[filament_extruder_id]==0.25}0.17{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
],
"filament_infill_max_speed": [
"200"
],
"filament_max_volumetric_speed": [
"24"
],
"filament_infill_max_crossing_speed": [
"120"
],
"name": "*PET05HFXL*",
"filament_settings_id": [
"*PET05HFXL*"
],
"type": "filament"
}
Version history
View full history with diffs →- v1 created 2026-05-19 11:27