Bambu PPS-CF @BBL H2S

Bambu Lab · PPS-CF · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pps

→

Bambu PPS-CF @base

→

Bambu PPS-CF @BBL H2S

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

fdm_filament_template_direct_dual

Compatible printers (3)

Bambu Lab H2S 0.4 nozzle
Bambu Lab H2S 0.6 nozzle
Bambu Lab H2S 0.8 nozzle

Settings

Basic information

Material variant: PPS-CF inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.26 inherited
Cost (/kg): 175 inherited

Print temperature

Nozzle (initial layer) (°C): 320 overridden
was 320 (inherited)
Nozzle (other layers) (°C): 320 overridden
was 320 (inherited)

Cooling

Fan minimum (%): 0 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 inherited
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 10 via fdm_filament_template_direct_dual

Flow

Flow ratio: 0.96 overridden
was 0.96 (inherited)
Max volumetric speed (mm³/s): 6 overridden
was 6 (inherited)

Retraction

Retraction length (mm): nil via fdm_filament_template_direct_dual
Retraction speed (mm/s): nil via fdm_filament_template_direct_dual
Deretraction speed (mm/s): nil via fdm_filament_template_direct_dual

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	110 inherited	110 inherited
High Temp Plate	110 inherited	110 inherited
Textured PEI Plate	110 inherited	110 inherited
Cool Plate SuperTack	0 inherited	0 inherited

Other settings

additional fan full speed layer: 0 inherited
chamber temperatures: 65 overridden
was 60 (inherited)
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab H2S 0.4 nozzle, Bambu Lab H2S 0.6 nozzle, Bambu Lab H2S 0.8 nozzle overridden
counter coef 2: 0.0003 overridden
counter coef 3: -0.0033 overridden
counter limit max: 0.0036 overridden
counter limit min: -0.0033 overridden
description: When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials. inherited
filament adaptive volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament adhesiveness category: 801 inherited
filament bridge speed: 25, 25 via fdm_filament_template_direct_dual
filament change length: 4 overridden
filament cooling before tower: 10, 10 overridden
filament dev ams drying ams limitations: -1 inherited
filament dev ams drying heat distortion temperature: 165 inherited
filament dev ams drying temperature: 65, 85, 65, 85 inherited
filament dev ams drying time: 12, 12, 12, 12 inherited
filament dev chamber drying bed temperature: 100 inherited
filament dev drying cooling temperature: 150 inherited
filament dev drying softening temperature: 150 inherited
filament enable overhang speed: 1, 1 via fdm_filament_template_direct_dual
filament extruder variant: Direct Drive Standard, Direct Drive High Flow via fdm_filament_template_direct_dual
filament flush temp: 0, 0 via fdm_filament_template_direct_dual
filament flush volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament id: GFT02 inherited
filament is support: 0 inherited
filament long retractions when cut: nil, nil via fdm_filament_template_direct_dual
filament minimal purge on wipe tower: 15 inherited
filament overhang 1 4 speed: 0, 0 via fdm_filament_template_direct_dual
filament overhang 2 4 speed: 50, 50 via fdm_filament_template_direct_dual
filament overhang 3 4 speed: 30, 30 via fdm_filament_template_direct_dual
filament overhang 4 4 speed: 10, 10 via fdm_filament_template_direct_dual
filament overhang totally speed: 10, 10 via fdm_filament_template_direct_dual
filament pre cooling temperature: 0, 0 via fdm_filament_template_direct_dual
filament pre cooling temperature nc: 0, 0 via fdm_filament_template_direct_dual
filament prime volume: 30 overridden
filament ramming travel time: 0, 0 overridden
filament ramming travel time nc: 0, 0 via fdm_filament_template_direct_dual
filament ramming volumetric speed: -1, -1 via fdm_filament_template_direct_dual
filament ramming volumetric speed nc: -1, -1 via fdm_filament_template_direct_dual
filament retract before wipe: nil, nil via fdm_filament_template_direct_dual
filament retract length nc: 14, 14 via fdm_filament_template_direct_dual
filament retract restart extra: nil, nil via fdm_filament_template_direct_dual
filament retract when changing layer: nil, nil via fdm_filament_template_direct_dual
filament retraction distances when cut: nil, nil via fdm_filament_template_direct_dual
filament retraction minimum travel: nil, nil via fdm_filament_template_direct_dual
filament soluble: 0 inherited
filament wipe: nil, nil via fdm_filament_template_direct_dual
filament wipe distance: nil, nil via fdm_filament_template_direct_dual
filament z hop: nil, nil via fdm_filament_template_direct_dual
filament z hop types: nil, nil via fdm_filament_template_direct_dual
full fan speed layer: 0 inherited
hole coef 2: -0.0033 overridden
hole coef 3: 0.1176 overridden
hole limit max: 0.1176 overridden
hole limit min: 0.035 overridden
impact strength z: 2.8 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 0, 0 overridden
nozzle temperature range high: 340 inherited
nozzle temperature range low: 310 inherited
overhang fan speed: 30 inherited
overhang fan threshold: 25% inherited
override process overhang speed: 0, 0 via fdm_filament_template_direct_dual
reduce fan stop start freq: 0 inherited
required nozzle HRC: 40 inherited
retraction distances when ec: 0, 0 overridden
setting id: GFST02_05 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 220 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 via fdm_filament_template_direct_dual

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "175"
  ],
  "filament_type": [
    "PPS-CF"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "110"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.26"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "320",
    "320"
  ],
  "overhang_fan_speed": [
    "30"
  ],
  "filament_flow_ratio": [
    "0.96",
    "0.96"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "40"
  ],
  "slow_down_min_speed": [
    "10",
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "220"
  ],
  "filament_retraction_length": [
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "110"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "110"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "6",
    "6"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "320",
    "320"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "textured_plate_temp": [
    "110"
  ],
  "chamber_temperatures": [
    "65"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "filament_dev_ams_drying_time": [
    "12",
    "12",
    "12",
    "12"
  ],
  "nozzle_temperature_range_low": [
    "310"
  ],
  "nozzle_temperature_range_high": [
    "340"
  ],
  "filament_adhesiveness_category": [
    "801"
  ],
  "textured_plate_temp_initial_layer": [
    "110"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "filament_dev_ams_drying_temperature": [
    "65",
    "85",
    "65",
    "85"
  ],
  "filament_dev_ams_drying_ams_limitations": [
    "-1"
  ],
  "filament_dev_drying_cooling_temperature": [
    "150"
  ],
  "filament_dev_drying_softening_temperature": [
    "150"
  ],
  "filament_dev_chamber_drying_bed_temperature": [
    "100"
  ],
  "filament_dev_ams_drying_heat_distortion_temperature": [
    "165"
  ],
  "description": "When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.",
  "filament_id": "GFT02",
  "impact_strength_z": [
    "2.8"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "filament_bridge_speed": [
    "25",
    "25"
  ],
  "long_retractions_when_ec": [
    "0",
    "0"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_retract_length_nc": [
    "14",
    "14"
  ],
  "filament_overhang_1_4_speed": [
    "0",
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "50",
    "50"
  ],
  "filament_overhang_3_4_speed": [
    "30",
    "30"
  ],
  "filament_overhang_4_4_speed": [
    "10",
    "10"
  ],
  "retraction_distances_when_ec": [
    "0",
    "0"
  ],
  "filament_cooling_before_tower": [
    "10",
    "10"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_enable_overhang_speed": [
    "1",
    "1"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10",
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "0",
    "0"
  ],
  "override_process_overhang_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_pre_cooling_temperature_nc": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "-1",
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "setting_id": "GFST02_05",
  "hole_coef_2": [
    "-0.0033"
  ],
  "hole_coef_3": [
    "0.1176"
  ],
  "counter_coef_2": [
    "0.0003"
  ],
  "counter_coef_3": [
    "-0.0033"
  ],
  "hole_limit_max": [
    "0.1176"
  ],
  "hole_limit_min": [
    "0.035"
  ],
  "counter_limit_max": [
    "0.0036"
  ],
  "counter_limit_min": [
    "-0.0033"
  ],
  "compatible_printers": [
    "Bambu Lab H2S 0.4 nozzle",
    "Bambu Lab H2S 0.6 nozzle",
    "Bambu Lab H2S 0.8 nozzle"
  ],
  "filament_prime_volume": [
    "30"
  ],
  "filament_change_length": [
    "4"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "name": "Bambu PPS-CF @BBL H2S"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:16