PolyLite Dual PLA

Snapmaker · PLA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*fdm_filament_common*

→

*fdm_filament_pla*

→

*PolyLite PLA @base*

→

PolyLite Dual PLA

Settings

Basic information

Material variant: PLA inherited
Vendor: Snapmaker inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 90 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 210 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 15 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	60 inherited

Other settings

additional cooling fan speed: 70 inherited
bed type: Hot Plate inherited
bridge fan speed: 100 inherited
compatible printers condition: (printer_model=="Snapmaker A250 Dual" or printer_model=="Snapmaker A250 Dual BKit" or printer_model=="Snapmaker A250 Dual QS+B Kit" or printer_model=="Snapmaker A250 Dual QSKit" or printer_model=="Snapmaker A350 Dual" or printer_model=="Snapmaker A350 Dual BKit" or printer_model=="Snapmaker A350 Dual QS+B Kit" or printer_model=="Snapmaker A350 Dual QSKit" or printer_model=="Snapmaker Artisan") and (nozzle_diameter[0]=="0.4" or nozzle_diameter[0]=="0.6" or nozzle_diameter[0]=="0.8") overridden
cooling: 1 inherited
enable pressure advance: 1 inherited
fan always on: 1 inherited
filament colour: #8269AC inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 0 inherited
filament deretract speed: nil inherited
filament load time: 0 inherited
filament loading speed: 25 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 0 inherited
filament multitool ramming: 0 inherited
filament multitool ramming volume: 0 inherited
filament retract before travel: nil inherited
filament retract before wipe: nil inherited
filament retract layer change: nil inherited
filament retract length: 1.2 inherited
filament retract lift: nil inherited
filament retract restart extra: nil inherited
filament retract speed: nil inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 25 inherited
filament unloading speed start: 3 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
full fan speed layer: 0 inherited
idle temperature: 154 inherited
overhang fan threshold: 0% inherited
start filament gcode: M900 K0.04 ;override pressure advance value inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "bed_type": [
    "Hot Plate"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "90"
  ],
  "filament_wipe": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Snapmaker"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "154"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "0"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "start_filament_gcode": [
    "M900 K0.04 ;override pressure advance value"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_cooling_moves": [
    "0"
  ],
  "filament_loading_speed": [
    "25"
  ],
  "filament_retract_speed": [
    "nil"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "filament_retract_length": [
    "1.2"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_unloading_speed": [
    "25"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_layer_change": [
    "nil"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_before_travel": [
    "nil"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "3"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "filament_multitool_ramming_volume": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "0"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_colour": [
    "#8269AC"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "compatible_printers_condition": [
    "(printer_model==\"Snapmaker A250 Dual\" or printer_model==\"Snapmaker A250 Dual BKit\" or printer_model==\"Snapmaker A250 Dual QS+B Kit\" or printer_model==\"Snapmaker A250 Dual QSKit\" or printer_model==\"Snapmaker A350 Dual\" or printer_model==\"Snapmaker A350 Dual BKit\" or printer_model==\"Snapmaker A350 Dual QS+B Kit\" or printer_model==\"Snapmaker A350 Dual QSKit\" or printer_model==\"Snapmaker Artisan\") and (nozzle_diameter[0]==\"0.4\" or nozzle_diameter[0]==\"0.6\" or nozzle_diameter[0]==\"0.8\")"
  ],
  "name": "PolyLite Dual PLA",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:06