fdm_filament_common

Snapmaker · OTHER · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inherited from this (8)

Settings

Basic information

Vendor: Snapmaker overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 0 overridden
Cost (/kg): 0 overridden

Print temperature

Nozzle (initial layer) (°C): 200 overridden
Nozzle (other layers) (°C): 200 overridden

Cooling

Fan minimum (%): 35 overridden
Fan maximum (%): 100 overridden
Disable fan for first N layers: 2 overridden
Full fan if layer below (sec): 60 overridden
Slow down if layer below (sec): 8 overridden
Min speed when slowed (mm/s): 10 overridden

Flow

Flow ratio: 1 overridden
Max volumetric speed (mm³/s): 0 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 overridden	60 overridden

Other settings

bed type: Hot Plate overridden
bridge fan speed: 100 overridden
cooling: 1 overridden
enable pressure advance: 0 overridden
fan always on: 0 overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 0 overridden
filament deretract speed: nil overridden
filament load time: 0 overridden
filament loading speed: 25 overridden
filament loading speed start: 3 overridden
filament minimal purge on wipe tower: 0 overridden
filament multitool ramming: 0 overridden
filament multitool ramming volume: 0 overridden
filament retract before travel: nil overridden
filament retract before wipe: nil overridden
filament retract layer change: nil overridden
filament retract length: nil overridden
filament retract lift: nil overridden
filament retract restart extra: nil overridden
filament retract speed: nil overridden
filament soluble: 0 overridden
filament toolchange delay: 0 overridden
filament unload time: 0 overridden
filament unloading speed: 25 overridden
filament unloading speed start: 3 overridden
filament wipe: nil overridden
filament wipe distance: nil overridden
full fan speed layer: 0 overridden
idle temperature: 140 overridden
overhang fan threshold: 95% overridden
start filament gcode: M900 K0.04 ;override pressure advance value overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "bed_type": [
    "Hot Plate"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "35"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_wipe": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Snapmaker"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "0"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "140"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "0"
  ],
  "nozzle_temperature": [
    "200"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "start_filament_gcode": [
    "M900 K0.04 ;override pressure advance value"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_cooling_moves": [
    "0"
  ],
  "filament_loading_speed": [
    "25"
  ],
  "filament_retract_speed": [
    "nil"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "filament_retract_length": [
    "nil"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_unloading_speed": [
    "25"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "0"
  ],
  "filament_retract_layer_change": [
    "nil"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_before_travel": [
    "nil"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "3"
  ],
  "nozzle_temperature_initial_layer": [
    "200"
  ],
  "filament_multitool_ramming_volume": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "0"
  ],
  "name": "*fdm_filament_common*",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:32