fdm_filament_pa

Snapmaker · PA-CF · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*fdm_filament_common*

→

*fdm_filament_pa*

Inherited from this (3)

Settings

Basic information

Material variant: PA-CF overridden
Vendor: Snapmaker inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.09 overridden
was 0 (inherited)
Cost (/kg): 150 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 255 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 35 (inherited)
Fan maximum (%): 65 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 2 (inherited)
Full fan if layer below (sec): 20 overridden
was 60 (inherited)
Slow down if layer below (sec): 20 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 8 overridden
was 0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	90 overridden was 60	95 overridden was 60

Other settings

bed type: Hot Plate inherited
bridge fan speed: 60 overridden
was 100 (inherited)
cooling: 1 overridden
was 1 (inherited)
enable pressure advance: 0 inherited
fan always on: 1 overridden
was 0 (inherited)
filament colour: #3D3C39 overridden
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 0 inherited
filament deretract speed: nil overridden
was nil (inherited)
filament load time: 0 inherited
filament loading speed: 25 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 0 inherited
filament multitool ramming: 0 inherited
filament multitool ramming volume: 0 inherited
filament notes: !! It needs to be dried before use. overridden
filament retract before travel: 0 overridden
was nil (inherited)
filament retract before wipe: nil inherited
filament retract layer change: nil overridden
was nil (inherited)
filament retract length: 2 overridden
was nil (inherited)
filament retract lift: nil overridden
was nil (inherited)
filament retract restart extra: nil inherited
filament retract speed: 36 overridden
was nil (inherited)
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 25 inherited
filament unloading speed start: 3 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
full fan speed layer: 3 overridden
was 0 (inherited)
idle temperature: 203 overridden
was 140 (inherited)
overhang fan threshold: 0% overridden
was 95% (inherited)
start filament gcode: M900 K0.04 ;override pressure advance value overridden
was M900 K0.04 ;override pressure advance value (inherited)

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "bed_type": [
    "Hot Plate"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "65"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "150"
  ],
  "filament_wipe": [
    "nil"
  ],
  "hot_plate_temp": [
    "95"
  ],
  "filament_vendor": [
    "Snapmaker"
  ],
  "bridge_fan_speed": [
    "60"
  ],
  "filament_density": [
    "1.09"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "203"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "0"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M900 K0.04 ;override pressure advance value"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_cooling_moves": [
    "0"
  ],
  "filament_loading_speed": [
    "25"
  ],
  "filament_retract_speed": [
    "36"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "filament_retract_length": [
    "2"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_unloading_speed": [
    "25"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_layer_change": [
    "nil"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_before_travel": [
    "0"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "3"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "filament_multitool_ramming_volume": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "0"
  ],
  "filament_type": [
    "PA-CF"
  ],
  "filament_notes": [
    "!! It needs to be dried before use.\n"
  ],
  "filament_colour": [
    "#3D3C39"
  ],
  "name": "*fdm_filament_pa*",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:32