Snapmaker Dual PLA Silk @base

Snapmaker · PLA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*fdm_filament_common*

→

*fdm_filament_pla*

→

*Snapmaker Dual PLA Silk @base*

Inherited from this (2)

Settings

Basic information

Material variant: PLA inherited
Vendor: Snapmaker inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.32 overridden
was 1.24 (inherited)
Cost (/kg): 70 overridden
was 60 (inherited)

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 210 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 12 overridden
was 14 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	65 overridden was 60	60 inherited

Other settings

additional cooling fan speed: 70 inherited
bed type: Hot Plate inherited
bridge fan speed: 100 inherited
cooling: 1 inherited
enable pressure advance: 1 inherited
end filament gcode: M104 S{idle_temperature[current_extruder]} ;standby T{current_extruder} overridden
was — (inherited)
fan always on: 1 inherited
filament colour: #CF942B overridden
was #F8C827 (inherited)
filament cooling final speed: 60 overridden
was 3.4 (inherited)
filament cooling initial speed: 35 overridden
was 2.2 (inherited)
filament cooling moves: 2 overridden
was 0 (inherited)
filament deretract speed: nil inherited
filament load time: 2 overridden
was 0 (inherited)
filament loading speed: 35 overridden
was 25 (inherited)
filament loading speed start: 35 overridden
was 3 (inherited)
filament minimal purge on wipe tower: 0 inherited
filament multitool ramming: 0 inherited
filament multitool ramming volume: 0 inherited
filament retract before travel: nil inherited
filament retract before wipe: nil inherited
filament retract layer change: nil inherited
filament retract length: 0.5 overridden
was 1.2 (inherited)
filament retract lift: nil inherited
filament retract restart extra: nil inherited
filament retract speed: nil inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 2 overridden
was 0 (inherited)
filament unloading speed: 35 overridden
was 25 (inherited)
filament unloading speed start: 35 overridden
was 3 (inherited)
filament wipe: nil inherited
filament wipe distance: nil inherited
full fan speed layer: 0 inherited
idle temperature: 154 inherited
overhang fan threshold: 0% inherited
start filament gcode: M900 K0.04 ;override pressure advance value inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "bed_type": [
    "Hot Plate"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "70"
  ],
  "filament_wipe": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Snapmaker"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "1.32"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "154"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "M104 S{idle_temperature[current_extruder]} ;standby T{current_extruder}"
  ],
  "filament_load_time": [
    "2"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "2"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "start_filament_gcode": [
    "M900 K0.04 ;override pressure advance value"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_cooling_moves": [
    "2"
  ],
  "filament_loading_speed": [
    "35"
  ],
  "filament_retract_speed": [
    "nil"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "filament_retract_length": [
    "0.5"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "filament_cooling_final_speed": [
    "60"
  ],
  "filament_loading_speed_start": [
    "35"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "65"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_layer_change": [
    "nil"
  ],
  "filament_cooling_initial_speed": [
    "35"
  ],
  "filament_retract_before_travel": [
    "nil"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "35"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "filament_multitool_ramming_volume": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "0"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_colour": [
    "#CF942B"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "name": "*Snapmaker Dual PLA Silk @base*",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:06