COEX NYLEX UNFILLED @BBL X1C

COEX 3D · PA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

COEX NYLEX UNFILLED @base

→

COEX NYLEX UNFILLED @BBL X1C

Compatible printers (9)

Bambu Lab P1S 0.4 nozzle
Bambu Lab P1S 0.6 nozzle
Bambu Lab P1S 0.8 nozzle
Bambu Lab X1 Carbon 0.4 nozzle
Bambu Lab X1 Carbon 0.6 nozzle
Bambu Lab X1 Carbon 0.8 nozzle
Bambu Lab X1E 0.4 nozzle
Bambu Lab X1E 0.6 nozzle
Bambu Lab X1E 0.8 nozzle

Settings

Basic information

Material variant: PA inherited
Vendor: COEX 3D inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.08 inherited
Cost (/kg): 85.00 inherited

Print temperature

Nozzle (initial layer) (°C): 260 inherited
Nozzle (other layers) (°C): 260 inherited
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 100 overridden
was 0 (inherited)
Fan maximum (%): 100 overridden
was 30 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 10 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.98 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 16 overridden
was 11 (inherited)

Retraction

Retraction length (mm): 2.5 inherited
Retraction speed (mm/s): 40 inherited
Deretraction speed (mm/s): 40 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	100 inherited	100 inherited
High Temp Plate	100 inherited	100 inherited
Textured PEI Plate	100 inherited	100 inherited

Other settings

bed temperature: 100 inherited
bed temperature initial layer: 100 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle overridden
was — (inherited)
disable fan first layers: 4 inherited
enable pressure advance: 1 inherited
filament id: CXPAUB21 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: 70% inherited
filament retract layer change: 1 inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 1 inherited
filament retraction minimum travel: 2 inherited
filament soluble: 0 inherited
filament wipe: 1 inherited
filament wipe distance: 2 inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 300 inherited
nozzle temperature range low: 260 inherited
overhang fan speed: 60 inherited
overhang fan threshold: 95% inherited
pressure advance: 0.02 inherited
reduce fan stop start freq: 0 inherited
setting id: CXPAUB21_01 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "85.00"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.08"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "60"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "10"
  ],
  "filament_wipe_distance": [
    "2"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "40"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "2.5"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "40"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "1"
  ],
  "nozzle_temperature_range_low": [
    "260"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "filament_id": "CXPAUB21",
  "bed_temperature": [
    "100"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "compatible_prints": [],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "Bambu Lab X1 Carbon 0.4 nozzle",
    "Bambu Lab X1 Carbon 0.6 nozzle",
    "Bambu Lab X1 Carbon 0.8 nozzle",
    "Bambu Lab P1S 0.4 nozzle",
    "Bambu Lab P1S 0.6 nozzle",
    "Bambu Lab P1S 0.8 nozzle",
    "Bambu Lab X1E 0.4 nozzle",
    "Bambu Lab X1E 0.6 nozzle",
    "Bambu Lab X1E 0.8 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "disable_fan_first_layers": [
    "4"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "100"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "1"
  ],
  "setting_id": "CXPAUB21_01",
  "name": "COEX NYLEX UNFILLED  @BBL X1C"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:06