COEX NYLEX UNFILLED @base

COEX 3D · PA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

COEX NYLEX UNFILLED @base

Inherited from this (1)

COEX NYLEX UNFILLED @BBL X1C

Settings

Basic information

Material variant: PA overridden
was PA (inherited)
Vendor: COEX 3D overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.08 overridden
was 1.04 (inherited)
Cost (/kg): 85.00 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 270 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 0 overridden
was 0 (inherited)
Fan maximum (%): 30 overridden
was 60 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 10 inherited
Slow down if layer below (sec): 5 overridden
was 2 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 11 overridden
was 8 (inherited)

Retraction

Retraction length (mm): 2.5 overridden
was 1.0 (inherited)
Retraction speed (mm/s): 40 overridden
was nil (inherited)
Deretraction speed (mm/s): 40 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	100 inherited	100 inherited
High Temp Plate	100 inherited	100 inherited
Textured PEI Plate	100 inherited	100 inherited

Other settings

bed temperature: 100 overridden
bed temperature initial layer: 100 overridden
bed type: Cool Plate inherited
disable fan first layers: 4 overridden
enable pressure advance: 1 overridden
filament id: CXPAUB21 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: 70% overridden
was nil (inherited)
filament retract layer change: 1 overridden
filament retract restart extra: nil inherited
filament retract when changing layer: 1 overridden
was nil (inherited)
filament retraction minimum travel: 2 overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: 1 overridden
was nil (inherited)
filament wipe distance: 2 overridden
was nil (inherited)
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 overridden
was 0 (inherited)
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 300 inherited
nozzle temperature range low: 260 inherited
overhang fan speed: 60 inherited
overhang fan threshold: 95% inherited
pressure advance: 0.02 overridden
reduce fan stop start freq: 0 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 100 overridden
was 108 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "85.00"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.08"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "60"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "10"
  ],
  "filament_wipe_distance": [
    "2"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "40"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "2.5"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "40"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "11"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "1"
  ],
  "nozzle_temperature_range_low": [
    "260"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "filament_id": "CXPAUB21",
  "bed_temperature": [
    "100"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "compatible_prints": [],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [],
  "enable_pressure_advance": [
    "1"
  ],
  "disable_fan_first_layers": [
    "4"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "100"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "1"
  ],
  "name": "COEX NYLEX UNFILLED @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:50