QIDI PETG Translucent @Qidi Q2 0.2 nozzle

QIDI · PETG · 0.20mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_q_common

→

QIDI PETG Translucent@Q2-Series

→

QIDI PETG Translucent @Qidi Q2 0.2 nozzle

Compatible printers (1)

Qidi Q2 0.2 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: QIDI inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 250 inherited
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 1 overridden
was 8 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	80 inherited	80 inherited
Cool Plate SuperTack	70 inherited	70 inherited

Other settings

activate air filtration: 1 inherited
additional cooling fan speed: 0 inherited
additional cooling fan speed unseal: 0 inherited
bed type: Cool Plate inherited
box temperature: 0 inherited
box temperature range high: 45 inherited
box temperature range low: 0 inherited
compatible printers: Qidi Q2 0.2 nozzle overridden
was — (inherited)
complete print exhaust fan speed: 0 inherited
dont slow down outer wall: 0 inherited
during print exhaust fan speed: 100 inherited
enable pressure advance: 1 inherited
filament adhesiveness category: 300 inherited
filament dev ams drying ams limitations: 1 inherited
filament dev ams drying heat distortion temperature: 45.0 inherited
filament dev ams drying temperature: 40.0, 40.0, 40.0, 40.0 inherited
filament dev ams drying time: 8.0, 8.0, 8.0, 8.0 inherited
filament dev chamber drying bed temperature: 90.0 inherited
filament dev chamber drying time: 12.0 inherited
filament dev drying cooling temperature: 35.0 inherited
filament dev drying softening temperature: 40.0 inherited
filament flush temp: 0 inherited
filament flush volumetric speed: 0 inherited
filament id: QD_1_1_45 inherited
filament long retractions when ec: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0 inherited
filament ramming travel time: 0 inherited
filament ramming volumetric speed: -1 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when ec: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament tower interface pre extrusion dist: 10 inherited
filament tower interface pre extrusion length: 0 inherited
filament tower interface print temp: -1 inherited
filament tower interface purge volume: 20 inherited
filament tower ironing area: 4 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
impact strength z: 10.6 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 10% inherited
pressure advance: 0.054 overridden
was 0.054 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSG99 overridden
was GFSG99 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "box_temperature": [
    "0"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "QIDI"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.054"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "chamber_temperature": [
    "0"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_flush_temp": [
    "0"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament start gcode"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "box_temperature_range_low": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "box_temperature_range_high": [
    "45"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "filament_tower_ironing_area": [
    "4"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_dev_ams_drying_time": [
    "8.0",
    "8.0",
    "8.0",
    "8.0"
  ],
  "filament_ramming_travel_time": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "100"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_flush_volumetric_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_dev_chamber_drying_time": [
    "12.0"
  ],
  "filament_pre_cooling_temperature": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "filament_long_retractions_when_ec": [
    "nil"
  ],
  "filament_ramming_volumetric_speed": [
    "-1"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "additional_cooling_fan_speed_unseal": [
    "0"
  ],
  "filament_dev_ams_drying_temperature": [
    "40.0",
    "40.0",
    "40.0",
    "40.0"
  ],
  "filament_tower_interface_print_temp": [
    "-1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_ec": [
    "nil"
  ],
  "filament_tower_interface_purge_volume": [
    "20"
  ],
  "filament_dev_ams_drying_ams_limitations": [
    "1"
  ],
  "filament_dev_drying_cooling_temperature": [
    "35.0"
  ],
  "filament_dev_drying_softening_temperature": [
    "40.0"
  ],
  "filament_dev_chamber_drying_bed_temperature": [
    "90.0"
  ],
  "filament_tower_interface_pre_extrusion_dist": [
    "10"
  ],
  "filament_tower_interface_pre_extrusion_length": [
    "0"
  ],
  "filament_dev_ams_drying_heat_distortion_temperature": [
    "45.0"
  ],
  "setting_id": "GFSG99",
  "filament_id": "QD_1_1_45",
  "impact_strength_z": [
    "10.6"
  ],
  "compatible_printers": [
    "Qidi Q2 0.2 nozzle"
  ],
  "supertack_plate_temp": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_adhesiveness_category": [
    "300"
  ],
  "supertack_plate_temp_initial_layer": [
    "70"
  ],
  "name": "QIDI PETG Translucent @Qidi Q2 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:00