fdm_filament_q_common

QIDI · PLA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inherited from this (108)

View all 108 →

Settings

Basic information

Material variant: PLA overridden
Vendor: QIDI overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 1.24 overridden
Cost (/kg): 0 overridden

Print temperature

Nozzle (initial layer) (°C): 210 overridden
Nozzle (other layers) (°C): 210 overridden
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 100 overridden
Fan maximum (%): 100 overridden
Disable fan for first N layers: 1 overridden
Full fan if layer below (sec): 60 overridden
Slow down if layer below (sec): 8 overridden
Min speed when slowed (mm/s): 20 overridden

Flow

Flow ratio: 0.98 overridden
Max volumetric speed (mm³/s): 24.5 overridden

Retraction

Retraction length (mm): nil overridden
Retraction speed (mm/s): nil overridden
Deretraction speed (mm/s): nil overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden	60 overridden
Engineering Plate	60 overridden	60 overridden
High Temp Plate	60 overridden	60 overridden

Other settings

activate air filtration: 1 overridden
additional cooling fan speed: 0 overridden
additional cooling fan speed unseal: 0 overridden
bed type: Cool Plate overridden
box temperature: 0 overridden
box temperature range high: 0 overridden
box temperature range low: 0 overridden
complete print exhaust fan speed: 0 overridden
dont slow down outer wall: 0 overridden
during print exhaust fan speed: 100 overridden
enable pressure advance: 1 overridden
filament dev ams drying ams limitations: 1 overridden
filament dev ams drying heat distortion temperature: 45.0 overridden
filament dev ams drying temperature: 40.0, 40.0, 40.0, 40.0 overridden
filament dev ams drying time: 8.0, 8.0, 8.0, 8.0 overridden
filament dev chamber drying bed temperature: 90.0 overridden
filament dev chamber drying time: 12.0 overridden
filament dev drying cooling temperature: 35.0 overridden
filament dev drying softening temperature: 40.0 overridden
filament flush temp: 0 overridden
filament flush volumetric speed: 0 overridden
filament long retractions when ec: nil overridden
filament minimal purge on wipe tower: 15 overridden
filament pre cooling temperature: 0 overridden
filament ramming travel time: 0 overridden
filament ramming volumetric speed: -1 overridden
filament retract before wipe: nil overridden
filament retract restart extra: nil overridden
filament retract when changing layer: nil overridden
filament retraction distances when ec: nil overridden
filament retraction minimum travel: nil overridden
filament soluble: 0 overridden
filament tower interface pre extrusion dist: 10 overridden
filament tower interface pre extrusion length: 0 overridden
filament tower interface print temp: -1 overridden
filament tower interface purge volume: 20 overridden
filament tower ironing area: 4 overridden
filament wipe: nil overridden
filament wipe distance: nil overridden
filament z hop: nil overridden
filament z hop types: nil overridden
full fan speed layer: 0 overridden
instantiation: false overridden
overhang fan speed: 100 overridden
overhang fan threshold: 95% overridden
pressure advance: 0.042 overridden
reduce fan stop start freq: 1 overridden
slow down for layer cooling: 1 overridden
temperature vitrification: 100 overridden

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "box_temperature": [
    "0"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "QIDI"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.042"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "chamber_temperature": [
    "0"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "filament_flush_temp": [
    "0"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament start gcode"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "box_temperature_range_low": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "box_temperature_range_high": [
    "0"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "filament_tower_ironing_area": [
    "4"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_dev_ams_drying_time": [
    "8.0",
    "8.0",
    "8.0",
    "8.0"
  ],
  "filament_ramming_travel_time": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "24.5"
  ],
  "during_print_exhaust_fan_speed": [
    "100"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_flush_volumetric_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_dev_chamber_drying_time": [
    "12.0"
  ],
  "filament_pre_cooling_temperature": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "filament_long_retractions_when_ec": [
    "nil"
  ],
  "filament_ramming_volumetric_speed": [
    "-1"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "additional_cooling_fan_speed_unseal": [
    "0"
  ],
  "filament_dev_ams_drying_temperature": [
    "40.0",
    "40.0",
    "40.0",
    "40.0"
  ],
  "filament_tower_interface_print_temp": [
    "-1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_ec": [
    "nil"
  ],
  "filament_tower_interface_purge_volume": [
    "20"
  ],
  "filament_dev_ams_drying_ams_limitations": [
    "1"
  ],
  "filament_dev_drying_cooling_temperature": [
    "35.0"
  ],
  "filament_dev_drying_softening_temperature": [
    "40.0"
  ],
  "filament_dev_chamber_drying_bed_temperature": [
    "90.0"
  ],
  "filament_tower_interface_pre_extrusion_dist": [
    "10"
  ],
  "filament_tower_interface_pre_extrusion_length": [
    "0"
  ],
  "filament_dev_ams_drying_heat_distortion_temperature": [
    "45.0"
  ],
  "name": "fdm_filament_q_common"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:37