Eryone PP-CF

Eryone · PP-CF · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

Eryone Standard PLA

→

Eryone PP-CF

Compatible printers (1)

Thinker X400 0.4 nozzle

Inherited from this (1)

Eryone PP-CF @0.2 nozzle

Settings

Basic information

Material variant: PP-CF overridden
was PLA (inherited)
Vendor: Eryone overridden
was Eryone (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 220 (inherited)
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 20 overridden
was 100 (inherited)
Fan maximum (%): 35 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 100 (inherited)
Slow down if layer below (sec): 10 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.92 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 8 overridden
was 12 (inherited)

Retraction

Retraction length (mm): 1 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	100 overridden was 65	100 overridden was 60
Textured PEI Plate	60 inherited	60 inherited

Custom G-code

filament_start_gcode overridden

; filament start gcode
SET_FAN_SPEED FAN=filter_fan SPEED=0

filament_end_gcode overridden

; filament end gcode 
SET_FAN_SPEED FAN=filter_fan SPEED=0

Other settings

activate air filtration: 0 inherited
activate chamber temp control: 0 inherited
additional cooling fan speed: 70 inherited
compatible printers: Thinker X400 0.4 nozzle overridden
was Thinker X400 0.4 nozzle (inherited)
complete print exhaust fan speed: 80 inherited
during print exhaust fan speed: 60 inherited
enable overhang bridge fan: 1 inherited
enable pressure advance: 0 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament id: EFL33 overridden
filament is support: 0 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 0 inherited
filament multitool ramming flow: 10 inherited
filament multitool ramming volume: 10 inherited
filament notes: Printing platform glue spraying overridden
was — (inherited)
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before wipe: nil inherited
filament retract lift above: nil inherited
filament retract lift below: nil inherited
filament retract lift enforce: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 260 inherited
nozzle temperature range low: 180 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 25% overridden
was 50% (inherited)
pressure advance: 0.02 inherited
reduce fan stop start freq: 1 inherited
required nozzle HRC: 0 inherited
setting id: EFSA33 overridden
slow down for layer cooling: 1 inherited
support material interface fan speed: 60 overridden
was -1 (inherited)
temperature vitrification: 160 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "35"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PP-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_notes": [
    "Printing platform glue spraying"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Eryone"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "compatible_prints": [],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \nSET_FAN_SPEED FAN=filter_fan SPEED=0"
  ],
  "filament_load_time": [
    "0"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "Thinker X400 0.4 nozzle"
  ],
  "filament_flow_ratio": [
    "0.92"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    "Eryone PP-CF"
  ],
  "filament_start_gcode": [
    "; filament start gcode\nSET_FAN_SPEED FAN=filter_fan SPEED=0"
  ],
  "filament_unload_time": [
    "0"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "temperature_vitrification": [
    "160"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_retraction_length": [
    "1"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "compatible_prints_condition": "",
  "filament_deretraction_speed": [
    "nil"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "180"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "support_material_interface_fan_speed": [
    "60"
  ],
  "setting_id": "EFSA33",
  "filament_id": "EFL33",
  "name": "Eryone PP-CF"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:45