Eryone Standard PLA

Eryone · PLA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Compatible printers (1)

Thinker X400 0.4 nozzle

Inherited from this (15)

View all 15 →

Settings

Basic information

Material variant: PLA overridden
Vendor: Eryone overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 1.24 overridden
Cost (/kg): 20 overridden

Print temperature

Nozzle (initial layer) (°C): 220 overridden
Nozzle (other layers) (°C): 220 overridden
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 100 overridden
Fan maximum (%): 100 overridden
Disable fan for first N layers: 1 overridden
Full fan if layer below (sec): 100 overridden
Slow down if layer below (sec): 5 overridden
Min speed when slowed (mm/s): 10 overridden

Flow

Flow ratio: 0.98 overridden
Max volumetric speed (mm³/s): 12 overridden

Retraction

Retraction length (mm): nil overridden
Retraction speed (mm/s): nil overridden
Deretraction speed (mm/s): nil overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden	60 overridden
Engineering Plate	60 overridden	60 overridden
High Temp Plate	65 overridden	60 overridden
Textured PEI Plate	60 overridden	60 overridden

Other settings

activate air filtration: 0 overridden
activate chamber temp control: 0 overridden
additional cooling fan speed: 70 overridden
compatible printers: Thinker X400 0.4 nozzle overridden
complete print exhaust fan speed: 80 overridden
during print exhaust fan speed: 60 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 0 overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament is support: 0 overridden
filament load time: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament minimal purge on wipe tower: 15 overridden
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract before wipe: nil overridden
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
filament retract when changing layer: nil overridden
filament retraction minimum travel: nil overridden
filament shrink: 100% overridden
filament soluble: 0 overridden
filament toolchange delay: 0 overridden
filament unload time: 0 overridden
filament unloading speed: 90 overridden
filament unloading speed start: 100 overridden
filament wipe: nil overridden
filament wipe distance: nil overridden
filament z hop: nil overridden
filament z hop types: nil overridden
full fan speed layer: 0 overridden
instantiation: false overridden
nozzle temperature range high: 260 overridden
nozzle temperature range low: 180 overridden
overhang fan speed: 100 overridden
overhang fan threshold: 50% overridden
pressure advance: 0.02 overridden
reduce fan stop start freq: 1 overridden
required nozzle HRC: 0 overridden
slow down for layer cooling: 1 overridden
support material interface fan speed: -1 overridden
temperature vitrification: 60 overridden

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "60"
  ],
  "filament_notes": [
    ""
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Eryone"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "compatible_prints": [],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "filament_load_time": [
    "0"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "Thinker X400 0.4 nozzle"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    "Eryone Standard PLA"
  ],
  "filament_start_gcode": [
    "; filament start gcode"
  ],
  "filament_unload_time": [
    "0"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "compatible_prints_condition": "",
  "filament_deretraction_speed": [
    "nil"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "65"
  ],
  "nozzle_temperature_range_low": [
    "180"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "name": "Eryone Standard PLA"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:45