Generic PVA @BBL P1P

Generic · PVA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pva

→

Generic PVA @base

→

Generic PVA @BBL P1P

Compatible printers (3)

Bambu Lab P1P 0.4 nozzle
Bambu Lab P1P 0.6 nozzle
Bambu Lab P1P 0.8 nozzle

Settings

Basic information

Material variant: PVA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 50 overridden
was 100 (inherited)
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 80 overridden
was 100 (inherited)
Slow down if layer below (sec): 7 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.95 overridden
was 0.95 (inherited)
Max volumetric speed (mm³/s): 16 overridden
was 16 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 inherited	35 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	65 overridden was 45	65 overridden was 45
Textured PEI Plate	65 overridden was 45	65 overridden was 45

Other settings

additional cooling fan speed: 70 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab P1P 0.4 nozzle, Bambu Lab P1P 0.6 nozzle, Bambu Lab P1P 0.8 nozzle overridden
description: This is a water-soluble support filament, and usually it is only for the support structure and not for the model body. Printing this filament is of many requirements, and to get better printing quality, please refer to this wiki: PVA Printing Guide. inherited
filament adaptive volumetric speed: 0, 0 overridden
filament extruder variant: Direct Drive Standard, Direct Drive High Flow overridden
filament flush temp: 0, 0 overridden
filament flush volumetric speed: 0, 0 overridden
filament id: GFS99 inherited
filament is support: 1 inherited
filament long retractions when cut: nil, nil overridden
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0, 0 overridden
filament ramming travel time: 0, 0 overridden
filament ramming volumetric speed: -1, -1 overridden
filament retract before wipe: nil, nil overridden
was nil (inherited)
filament retract restart extra: nil, nil overridden
was nil (inherited)
filament retract when changing layer: nil, nil overridden
was nil (inherited)
filament retraction distances when cut: nil, nil overridden
filament retraction minimum travel: nil, nil overridden
was nil (inherited)
filament soluble: 1 inherited
filament wipe: nil, nil overridden
was nil (inherited)
filament wipe distance: nil, nil overridden
was nil (inherited)
filament z hop: nil, nil overridden
was nil (inherited)
filament z hop types: nil, nil overridden
was nil (inherited)
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 0, 0 overridden
nozzle temperature range high: 250 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
retraction distances when ec: 0, 0 overridden
setting id: GFSS99_10 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 overridden

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "50"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PVA"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "65"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220",
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.95",
    "0.95"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "65"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "7"
  ],
  "fan_cooling_layer_time": [
    "80"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "65"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "16",
    "16"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220",
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "65"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "filament_is_support": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "description": "This is a water-soluble support filament, and usually it is only for the support structure and not for the model body. Printing this filament is of many requirements, and to get better printing quality, please refer to this wiki: PVA Printing Guide.",
  "filament_id": "GFS99",
  "setting_id": "GFSS99_10",
  "compatible_printers": [
    "Bambu Lab P1P 0.4 nozzle",
    "Bambu Lab P1P 0.6 nozzle",
    "Bambu Lab P1P 0.8 nozzle"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "long_retractions_when_ec": [
    "0",
    "0"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "retraction_distances_when_ec": [
    "0",
    "0"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "name": "Generic PVA @BBL P1P"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:45