fdm_filament_pva

Generic · PVA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pva

Inherited from this (38)

View all 38 →

Settings

Basic information

Material variant: PVA overridden
was PLA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 overridden
was 0 (inherited)
Cost (/kg): 20 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 35 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 overridden
was 3 (inherited)
Full fan if layer below (sec): 100 overridden
was 60 (inherited)
Slow down if layer below (sec): 4 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 15 overridden
was 0 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 overridden was 60	35 overridden was 60
Engineering Plate	0 overridden was 60	0 overridden was 60
High Temp Plate	45 overridden was 60	45 overridden was 60
Textured PEI Plate	45 overridden was 60	45 overridden was 60

Other settings

additional cooling fan speed: 70 overridden
bed type: Cool Plate inherited
filament is support: 1 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 1 overridden
was 0 (inherited)
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 250 overridden
nozzle temperature range low: 190 overridden
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 50% overridden
was 95% (inherited)
reduce fan stop start freq: 1 overridden
was 0 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 50 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PVA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "45"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "45"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "45"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "45"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_is_support": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "name": "fdm_filament_pva"
}

Version history

View full history with diffs →

v17 updated 2026-05-19 04:56
v16 updated 2026-05-19 04:55
v15 updated 2026-05-19 04:55
v14 updated 2026-05-19 04:53
v13 updated 2026-05-19 04:51
v12 updated 2026-05-19 04:51
v11 updated 2026-05-19 04:51
v10 updated 2026-05-19 04:49
v9 updated 2026-05-19 04:48
v8 updated 2026-05-19 04:46
v7 updated 2026-05-19 04:46
v6 updated 2026-05-19 04:46
v5 updated 2026-05-19 04:39
v4 updated 2026-05-19 04:34
v3 updated 2026-05-19 04:33
v2 updated 2026-05-19 04:33
v1 created 2026-05-19 04:33