FusRock ABS-GF @BBL H2D

FusRock · ABS-GF · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

FusRock ABS-GF @base

→

FusRock ABS-GF @BBL H2D

Compatible printers (3)

Bambu Lab H2D 0.4 nozzle
Bambu Lab H2D 0.6 nozzle
Bambu Lab H2D 0.8 nozzle

Settings

Basic information

Material variant: ABS-GF inherited
Vendor: FusRock inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.08 inherited
Cost (/kg): 13 inherited

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 12 inherited
Slow down if layer below (sec): 4 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.92 overridden
was 0.92 (inherited)
Max volumetric speed (mm³/s): 20 overridden
was 18 (inherited)

Retraction

Retraction length (mm): nil overridden
was 0.8 (inherited)
Retraction speed (mm/s): nil overridden
was 30 (inherited)
Deretraction speed (mm/s): nil overridden
was 0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	105 inherited	105 inherited
Textured PEI Plate	105 inherited	105 inherited
Cool Plate SuperTack	0 inherited	0 inherited

Custom G-code

filament_start_gcode overridden

; filament start gcode
M145 P1 ; set airduct mode to heating mode

Other settings

activate air filtration: 1 inherited
additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
chamber temperatures: 60 overridden
compatible printers: Bambu Lab H2D 0.4 nozzle, Bambu Lab H2D 0.6 nozzle, Bambu Lab H2D 0.8 nozzle overridden
complete print exhaust fan speed: 10 inherited
description: When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials（https://wiki.fusrock.com）. inherited
during print exhaust fan speed: 30 inherited
enable overhang bridge fan: 1 inherited
filament adhesiveness category: 200 inherited
filament extruder variant: Direct Drive Standard, Direct Drive High Flow overridden
was Direct Drive Standard (inherited)
filament id: OGFR00 inherited
filament long retractions when cut: nil, nil overridden
filament minimal purge on wipe tower: 15 inherited
filament notes: //EN 1.Be sure to read it carefully before using (https://wiki.fusrock.com). 2.When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials（https://wiki.fusrock.com）.\n3.Thank you for choosing us FusRock. *This setting may not be able to adapt to all models. In some cases, you need to modify and adjust the parameters by yourself to improve the printing effect. *FusRock 3D printing filaments are intended for general-purpose printing and have been tested under standard conditions. However, the performance and safety of printed objects are affected by multiple factors, including printing parameters, model design, usage environment, and the specific application. *By using FusRock materials, the user acknowledges and agrees to independently evaluate whether the printed parts are suitable for their intended use, and assumes all associated risks. *FusRock shall not be held liable for any damage, injury, or loss that may result from the use of printed products made with our materials, including but not limited to structural failure, functional defects, or safety hazards under actual usage conditions.Before applying printed parts in any critical, functional, or commercial context, thorough testing must be conducted. Except for the certifications explicitly stated for specific FusRock materials, our products are not certified for medical, aerospace, or life-support applications. //CN 1.使用前请务必仔细阅读（https://wiki.fusrock.com）。 2.打印该耗材时，可能会出现喷嘴堵塞、拉丝、翘边以及层间附着力不足等问题。为了获得更好的打印效果，请参考此维基页面：高温 / 工程材料打印技巧（https://wiki.fusrock.com）。 3.感谢您选择FusRock。 *此设置不一定能够适配所有模型，存在部分情况下需要您自行修改调整参数来提升打印效果。 *FusRock 3D打印耗材适用于通用打印用途，已在标准条件下进行测试。然而，打印成品的性能与安全性受多种因素影响，包括打印参数、模型设计、使用环境及实际用途。 *使用FusRock材料即表示用户已知悉并同意，自行评估打印件是否适用于其具体应用，并承担由此产生的全部风险。 *FusRock对使用本公司耗材打印的产品在实际应用中可能导致的任何损害、伤害或损失不承担任何责任，包括但不限于结构失效、功能异常或使用环境中的安全隐患。在将打印件应用于关键、功能性或商业性场景前，请务必进行充分测试。除FusRock已标明材料所获得的各项认证资质外，FusRock产品未取得医疗、航天或生命支持系统认证资质。 inherited
filament pre cooling temperature: 0, 0 overridden
filament ramming travel time: 0, 0 overridden
filament ramming volumetric speed: -1, -1 overridden
filament retract before wipe: nil, nil overridden
was 100% (inherited)
filament retract restart extra: nil, nil overridden
was nil (inherited)
filament retract when changing layer: nil, nil overridden
was 0 (inherited)
filament retraction distances when cut: nil, nil overridden
filament retraction minimum travel: nil, nil overridden
was 2 (inherited)
filament soluble: 0 inherited
filament wipe: nil, nil overridden
was 0 (inherited)
filament wipe distance: nil, nil overridden
was 2 (inherited)
filament z hop: nil, nil overridden
was 0.4 (inherited)
filament z hop types: nil, nil overridden
was Spiral Lift (inherited)
full fan speed layer: 0 inherited
impact strength z: 5.3 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 30 inherited
overhang fan threshold: 10% inherited
overhang threshold participating cooling: 100% inherited
pre start fan time: 0 inherited
reduce fan stop start freq: 0 inherited
setting id: GFSR00_03 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "13"
  ],
  "filament_type": [
    "ABS-GF"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "FusRock"
  ],
  "filament_density": [
    "1.08"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270",
    "270"
  ],
  "overhang_fan_speed": [
    "30"
  ],
  "filament_flow_ratio": [
    "0.92",
    "0.92"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\nM145 P1 ; set airduct mode to heating mode\n"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "12"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "20",
    "20"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260",
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "description": "When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials\uff08https://wiki.fusrock.com\uff09.",
  "filament_id": "OGFR00",
  "filament_notes": "//EN\n1.Be sure to read it carefully before using (https://wiki.fusrock.com).\n2.When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials\uff08https://wiki.fusrock.com\uff09.\\n3.Thank you for choosing us FusRock.\n*This setting may not be able to adapt to all models. In some cases, you need to modify and adjust the parameters by yourself to improve the printing effect.\n*FusRock 3D printing filaments are intended for general-purpose printing and have been tested under standard conditions. However, the performance and safety of printed objects are affected by multiple factors, including printing parameters, model design, usage environment, and the specific application.\n*By using FusRock materials, the user acknowledges and agrees to independently evaluate whether the printed parts are suitable for their intended use, and assumes all associated risks.\n*FusRock shall not be held liable for any damage, injury, or loss that may result from the use of printed products made with our materials, including but not limited to structural failure, functional defects, or safety hazards under actual usage conditions.Before applying printed parts in any critical, functional, or commercial context, thorough testing must be conducted. Except for the certifications explicitly stated for specific FusRock materials, our products are not certified for medical, aerospace, or life-support applications.\n//CN\n1.\u4f7f\u7528\u524d\u8bf7\u52a1\u5fc5\u4ed4\u7ec6\u9605\u8bfb\uff08https://wiki.fusrock.com\uff09\u3002\n2.\u6253\u5370\u8be5\u8017\u6750\u65f6\uff0c\u53ef\u80fd\u4f1a\u51fa\u73b0\u55b7\u5634\u5835\u585e\u3001\u62c9\u4e1d\u3001\u7fd8\u8fb9\u4ee5\u53ca\u5c42\u95f4\u9644\u7740\u529b\u4e0d\u8db3\u7b49\u95ee\u9898\u3002\u4e3a\u4e86\u83b7\u5f97\u66f4\u597d\u7684\u6253\u5370\u6548\u679c\uff0c\u8bf7\u53c2\u8003\u6b64\u7ef4\u57fa\u9875\u9762\uff1a\u9ad8\u6e29 / \u5de5\u7a0b\u6750\u6599\u6253\u5370\u6280\u5de7\uff08https://wiki.fusrock.com\uff09\u3002\n3.\u611f\u8c22\u60a8\u9009\u62e9FusRock\u3002\n*\u6b64\u8bbe\u7f6e\u4e0d\u4e00\u5b9a\u80fd\u591f\u9002\u914d\u6240\u6709\u6a21\u578b\uff0c\u5b58\u5728\u90e8\u5206\u60c5\u51b5\u4e0b\u9700\u8981\u60a8\u81ea\u884c\u4fee\u6539\u8c03\u6574\u53c2\u6570\u6765\u63d0\u5347\u6253\u5370\u6548\u679c\u3002\n*FusRock 3D\u6253\u5370\u8017\u6750\u9002\u7528\u4e8e\u901a\u7528\u6253\u5370\u7528\u9014\uff0c\u5df2\u5728\u6807\u51c6\u6761\u4ef6\u4e0b\u8fdb\u884c\u6d4b\u8bd5\u3002\u7136\u800c\uff0c\u6253\u5370\u6210\u54c1\u7684\u6027\u80fd\u4e0e\u5b89\u5168\u6027\u53d7\u591a\u79cd\u56e0\u7d20\u5f71\u54cd\uff0c\u5305\u62ec\u6253\u5370\u53c2\u6570\u3001\u6a21\u578b\u8bbe\u8ba1\u3001\u4f7f\u7528\u73af\u5883\u53ca\u5b9e\u9645\u7528\u9014\u3002\n*\u4f7f\u7528FusRock\u6750\u6599\u5373\u8868\u793a\u7528\u6237\u5df2\u77e5\u6089\u5e76\u540c\u610f\uff0c\u81ea\u884c\u8bc4\u4f30\u6253\u5370\u4ef6\u662f\u5426\u9002\u7528\u4e8e\u5176\u5177\u4f53\u5e94\u7528\uff0c\u5e76\u627f\u62c5\u7531\u6b64\u4ea7\u751f\u7684\u5168\u90e8\u98ce\u9669\u3002\n*FusRock\u5bf9\u4f7f\u7528\u672c\u516c\u53f8\u8017\u6750\u6253\u5370\u7684\u4ea7\u54c1\u5728\u5b9e\u9645\u5e94\u7528\u4e2d\u53ef\u80fd\u5bfc\u81f4\u7684\u4efb\u4f55\u635f\u5bb3\u3001\u4f24\u5bb3\u6216\u635f\u5931\u4e0d\u627f\u62c5\u4efb\u4f55\u8d23\u4efb\uff0c\u5305\u62ec\u4f46\u4e0d\u9650\u4e8e\u7ed3\u6784\u5931\u6548\u3001\u529f\u80fd\u5f02\u5e38\u6216\u4f7f\u7528\u73af\u5883\u4e2d\u7684\u5b89\u5168\u9690\u60a3\u3002\u5728\u5c06\u6253\u5370\u4ef6\u5e94\u7528\u4e8e\u5173\u952e\u3001\u529f\u80fd\u6027\u6216\u5546\u4e1a\u6027\u573a\u666f\u524d\uff0c\u8bf7\u52a1\u5fc5\u8fdb\u884c\u5145\u5206\u6d4b\u8bd5\u3002\u9664FusRock\u5df2\u6807\u660e\u6750\u6599\u6240\u83b7\u5f97\u7684\u5404\u9879\u8ba4\u8bc1\u8d44\u8d28\u5916\uff0cFusRock\u4ea7\u54c1\u672a\u53d6\u5f97\u533b\u7597\u3001\u822a\u5929\u6216\u751f\u547d\u652f\u6301\u7cfb\u7edf\u8ba4\u8bc1\u8d44\u8d28\u3002",
  "impact_strength_z": [
    "5.3"
  ],
  "pre_start_fan_time": [
    "0"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "during_print_exhaust_fan_speed": [
    "30"
  ],
  "filament_adhesiveness_category": [
    "200"
  ],
  "complete_print_exhaust_fan_speed": [
    "10"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "overhang_threshold_participating_cooling": [
    "100%"
  ],
  "setting_id": "GFSR00_03",
  "compatible_printers": [
    "Bambu Lab H2D 0.4 nozzle",
    "Bambu Lab H2D 0.6 nozzle",
    "Bambu Lab H2D 0.8 nozzle"
  ],
  "chamber_temperatures": [
    "60"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "name": "FusRock ABS-GF @BBL H2D"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:43