FusRock ABS-GF @base

FusRock · ABS-GF · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

FusRock ABS-GF @base

Inherited from this (5)

Settings

Basic information

Material variant: ABS-GF overridden
was PLA (inherited)
Vendor: FusRock overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.08 overridden
was 0 (inherited)
Cost (/kg): 13 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 35 (inherited)
Fan maximum (%): 30 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 12 overridden
was 60 (inherited)
Slow down if layer below (sec): 4 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 0.92 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 18 overridden
was 0 (inherited)

Retraction

Retraction length (mm): 0.8 overridden
was nil (inherited)
Retraction speed (mm/s): 30 overridden
was nil (inherited)
Deretraction speed (mm/s): 0 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Engineering Plate	105 overridden was 60	105 overridden was 60
High Temp Plate	105 overridden was 60	105 overridden was 60
Textured PEI Plate	105 overridden was 60	105 overridden was 60
Cool Plate SuperTack	0 overridden	0 overridden

Other settings

activate air filtration: 1 overridden
additional cooling fan speed: 0 overridden
bed type: Cool Plate inherited
complete print exhaust fan speed: 10 overridden
description: When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials（https://wiki.fusrock.com）. overridden
during print exhaust fan speed: 30 overridden
enable overhang bridge fan: 1 overridden
filament adhesiveness category: 200 overridden
filament extruder variant: Direct Drive Standard overridden
filament id: OGFR00 overridden
filament minimal purge on wipe tower: 15 inherited
filament notes: //EN 1.Be sure to read it carefully before using (https://wiki.fusrock.com). 2.When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials（https://wiki.fusrock.com）.\n3.Thank you for choosing us FusRock. *This setting may not be able to adapt to all models. In some cases, you need to modify and adjust the parameters by yourself to improve the printing effect. *FusRock 3D printing filaments are intended for general-purpose printing and have been tested under standard conditions. However, the performance and safety of printed objects are affected by multiple factors, including printing parameters, model design, usage environment, and the specific application. *By using FusRock materials, the user acknowledges and agrees to independently evaluate whether the printed parts are suitable for their intended use, and assumes all associated risks. *FusRock shall not be held liable for any damage, injury, or loss that may result from the use of printed products made with our materials, including but not limited to structural failure, functional defects, or safety hazards under actual usage conditions.Before applying printed parts in any critical, functional, or commercial context, thorough testing must be conducted. Except for the certifications explicitly stated for specific FusRock materials, our products are not certified for medical, aerospace, or life-support applications. //CN 1.使用前请务必仔细阅读（https://wiki.fusrock.com）。 2.打印该耗材时，可能会出现喷嘴堵塞、拉丝、翘边以及层间附着力不足等问题。为了获得更好的打印效果，请参考此维基页面：高温 / 工程材料打印技巧（https://wiki.fusrock.com）。 3.感谢您选择FusRock。 *此设置不一定能够适配所有模型，存在部分情况下需要您自行修改调整参数来提升打印效果。 *FusRock 3D打印耗材适用于通用打印用途，已在标准条件下进行测试。然而，打印成品的性能与安全性受多种因素影响，包括打印参数、模型设计、使用环境及实际用途。 *使用FusRock材料即表示用户已知悉并同意，自行评估打印件是否适用于其具体应用，并承担由此产生的全部风险。 *FusRock对使用本公司耗材打印的产品在实际应用中可能导致的任何损害、伤害或损失不承担任何责任，包括但不限于结构失效、功能异常或使用环境中的安全隐患。在将打印件应用于关键、功能性或商业性场景前，请务必进行充分测试。除FusRock已标明材料所获得的各项认证资质外，FusRock产品未取得医疗、航天或生命支持系统认证资质。 overridden
filament retract before wipe: 100% overridden
was nil (inherited)
filament retract restart extra: nil inherited
filament retract when changing layer: 0 overridden
was nil (inherited)
filament retraction minimum travel: 2 overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: 0 overridden
was nil (inherited)
filament wipe distance: 2 overridden
was nil (inherited)
filament z hop: 0.4 overridden
was nil (inherited)
filament z hop types: Spiral Lift overridden
was nil (inherited)
full fan speed layer: 0 inherited
impact strength z: 5.3 overridden
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 280 overridden
nozzle temperature range low: 240 overridden
overhang fan speed: 30 overridden
was 100 (inherited)
overhang fan threshold: 10% overridden
was 95% (inherited)
overhang threshold participating cooling: 100% overridden
pre start fan time: 0 overridden
reduce fan stop start freq: 0 overridden
was 0 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "13"
  ],
  "filament_type": [
    "ABS-GF"
  ],
  "filament_wipe": [
    "0"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "FusRock"
  ],
  "filament_density": [
    "1.08"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n\n"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "30"
  ],
  "filament_flow_ratio": [
    "0.92"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "Spiral Lift"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "12"
  ],
  "filament_wipe_distance": [
    "2"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "30"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "0.8"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "0"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "100%"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "0"
  ],
  "description": "When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials\uff08https://wiki.fusrock.com\uff09.",
  "filament_id": "OGFR00",
  "filament_notes": "//EN\n1.Be sure to read it carefully before using (https://wiki.fusrock.com).\n2.When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials\uff08https://wiki.fusrock.com\uff09.\\n3.Thank you for choosing us FusRock.\n*This setting may not be able to adapt to all models. In some cases, you need to modify and adjust the parameters by yourself to improve the printing effect.\n*FusRock 3D printing filaments are intended for general-purpose printing and have been tested under standard conditions. However, the performance and safety of printed objects are affected by multiple factors, including printing parameters, model design, usage environment, and the specific application.\n*By using FusRock materials, the user acknowledges and agrees to independently evaluate whether the printed parts are suitable for their intended use, and assumes all associated risks.\n*FusRock shall not be held liable for any damage, injury, or loss that may result from the use of printed products made with our materials, including but not limited to structural failure, functional defects, or safety hazards under actual usage conditions.Before applying printed parts in any critical, functional, or commercial context, thorough testing must be conducted. Except for the certifications explicitly stated for specific FusRock materials, our products are not certified for medical, aerospace, or life-support applications.\n//CN\n1.\u4f7f\u7528\u524d\u8bf7\u52a1\u5fc5\u4ed4\u7ec6\u9605\u8bfb\uff08https://wiki.fusrock.com\uff09\u3002\n2.\u6253\u5370\u8be5\u8017\u6750\u65f6\uff0c\u53ef\u80fd\u4f1a\u51fa\u73b0\u55b7\u5634\u5835\u585e\u3001\u62c9\u4e1d\u3001\u7fd8\u8fb9\u4ee5\u53ca\u5c42\u95f4\u9644\u7740\u529b\u4e0d\u8db3\u7b49\u95ee\u9898\u3002\u4e3a\u4e86\u83b7\u5f97\u66f4\u597d\u7684\u6253\u5370\u6548\u679c\uff0c\u8bf7\u53c2\u8003\u6b64\u7ef4\u57fa\u9875\u9762\uff1a\u9ad8\u6e29 / \u5de5\u7a0b\u6750\u6599\u6253\u5370\u6280\u5de7\uff08https://wiki.fusrock.com\uff09\u3002\n3.\u611f\u8c22\u60a8\u9009\u62e9FusRock\u3002\n*\u6b64\u8bbe\u7f6e\u4e0d\u4e00\u5b9a\u80fd\u591f\u9002\u914d\u6240\u6709\u6a21\u578b\uff0c\u5b58\u5728\u90e8\u5206\u60c5\u51b5\u4e0b\u9700\u8981\u60a8\u81ea\u884c\u4fee\u6539\u8c03\u6574\u53c2\u6570\u6765\u63d0\u5347\u6253\u5370\u6548\u679c\u3002\n*FusRock 3D\u6253\u5370\u8017\u6750\u9002\u7528\u4e8e\u901a\u7528\u6253\u5370\u7528\u9014\uff0c\u5df2\u5728\u6807\u51c6\u6761\u4ef6\u4e0b\u8fdb\u884c\u6d4b\u8bd5\u3002\u7136\u800c\uff0c\u6253\u5370\u6210\u54c1\u7684\u6027\u80fd\u4e0e\u5b89\u5168\u6027\u53d7\u591a\u79cd\u56e0\u7d20\u5f71\u54cd\uff0c\u5305\u62ec\u6253\u5370\u53c2\u6570\u3001\u6a21\u578b\u8bbe\u8ba1\u3001\u4f7f\u7528\u73af\u5883\u53ca\u5b9e\u9645\u7528\u9014\u3002\n*\u4f7f\u7528FusRock\u6750\u6599\u5373\u8868\u793a\u7528\u6237\u5df2\u77e5\u6089\u5e76\u540c\u610f\uff0c\u81ea\u884c\u8bc4\u4f30\u6253\u5370\u4ef6\u662f\u5426\u9002\u7528\u4e8e\u5176\u5177\u4f53\u5e94\u7528\uff0c\u5e76\u627f\u62c5\u7531\u6b64\u4ea7\u751f\u7684\u5168\u90e8\u98ce\u9669\u3002\n*FusRock\u5bf9\u4f7f\u7528\u672c\u516c\u53f8\u8017\u6750\u6253\u5370\u7684\u4ea7\u54c1\u5728\u5b9e\u9645\u5e94\u7528\u4e2d\u53ef\u80fd\u5bfc\u81f4\u7684\u4efb\u4f55\u635f\u5bb3\u3001\u4f24\u5bb3\u6216\u635f\u5931\u4e0d\u627f\u62c5\u4efb\u4f55\u8d23\u4efb\uff0c\u5305\u62ec\u4f46\u4e0d\u9650\u4e8e\u7ed3\u6784\u5931\u6548\u3001\u529f\u80fd\u5f02\u5e38\u6216\u4f7f\u7528\u73af\u5883\u4e2d\u7684\u5b89\u5168\u9690\u60a3\u3002\u5728\u5c06\u6253\u5370\u4ef6\u5e94\u7528\u4e8e\u5173\u952e\u3001\u529f\u80fd\u6027\u6216\u5546\u4e1a\u6027\u573a\u666f\u524d\uff0c\u8bf7\u52a1\u5fc5\u8fdb\u884c\u5145\u5206\u6d4b\u8bd5\u3002\u9664FusRock\u5df2\u6807\u660e\u6750\u6599\u6240\u83b7\u5f97\u7684\u5404\u9879\u8ba4\u8bc1\u8d44\u8d28\u5916\uff0cFusRock\u4ea7\u54c1\u672a\u53d6\u5f97\u533b\u7597\u3001\u822a\u5929\u6216\u751f\u547d\u652f\u6301\u7cfb\u7edf\u8ba4\u8bc1\u8d44\u8d28\u3002",
  "impact_strength_z": [
    "5.3"
  ],
  "pre_start_fan_time": [
    "0"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "during_print_exhaust_fan_speed": [
    "30"
  ],
  "filament_adhesiveness_category": [
    "200"
  ],
  "complete_print_exhaust_fan_speed": [
    "10"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "overhang_threshold_participating_cooling": [
    "100%"
  ],
  "name": "FusRock ABS-GF @base"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 04:49
v1 created 2026-05-19 04:43