Filatech HIPS @XL

Filatech · HIPS · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

→

Filatech HIPS @XL

Includes (2)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (2)

Settings

Basic information

Material variant: HIPS inherited
Vendor: Filatech inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.07 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 230 (inherited)
Nozzle (other layers) (°C): 225 overridden
was 225 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 20 (inherited)
Fan maximum (%): 20 overridden
was 20 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 10 overridden
was 10 (inherited)
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 via *ABSPG*

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 overridden was 100	105 overridden was 110

Other settings

bridge fan speed: 50 overridden
was 50 (inherited)
compatible printers condition: printer_model=~/.*XL.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 via *ABSXL*
cooling: 1 overridden
was 1 (inherited)
fan always on: 1 overridden
was 1 (inherited)
filament colour: #FFFFD7 inherited
filament cooling final speed: 50 via *ABSPG*
filament cooling initial speed: 10 via *ABSPG*
filament cooling moves: 5 via *ABSPG*
filament load time: 15 via *ABSPG*
filament loading speed: 14 via *ABSPG*
filament loading speed start: 19 via *ABSPG*
filament minimal purge on wipe tower: 35 via *ABSXL*
filament multitool ramming: 1 via *ABSXL*
filament multitool ramming flow: 40 via *ABSXL*
filament multitool ramming volume: 5 via *ABSXL*
filament ramming parameters: 120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6, via *ABSPG*
filament retract length toolchange: 20 via *ABSXL*
filament soluble: 1 inherited
filament toolchange delay: 0 inherited
filament travel max lift: 1.5 via *ABSXL*
filament travel ramping lift: 1 via *ABSXL*
filament travel slope: 1 via *ABSXL*
filament unload time: 12 via *ABSPG*
filament unloading speed: 20 via *ABSPG*
filament unloading speed start: 100 inherited
idle temperature: 100 via *ABSPG*
renamed from: Filatech HIPS @PG overridden
start filament gcode: M900 K{if nozzle_diameter[0]==0.4}0.04{elsif nozzle_diameter[0]==0.25}0.1{elsif nozzle_diameter[0]==0.3}0.06{elsif nozzle_diameter[0]==0.35}0.05{elsif nozzle_diameter[0]==0.5}0.03{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.01{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif} M142 S40 ; set heatbreak target temp via *ABSPG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.07"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "M900 K{if nozzle_diameter[0]==0.4}0.04{elsif nozzle_diameter[0]==0.25}0.1{elsif nozzle_diameter[0]==0.3}0.06{elsif nozzle_diameter[0]==0.35}0.05{elsif nozzle_diameter[0]==0.5}0.03{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.01{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S40 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "5"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6",
    ""
  ],
  "filament_cooling_final_speed": [
    "50"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "printer_model=~/.*XL.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8"
  ],
  "filament_cooling_initial_speed": [
    "10"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "HIPS"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "filament_colour": [
    "#FFFFD7"
  ],
  "bridge_fan_speed": [
    "50"
  ],
  "nozzle_temperature": [
    "225"
  ],
  "fan_cooling_layer_time": [
    "10"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "filament_vendor": [
    "Filatech"
  ],
  "filament_spool_weight": [
    ""
  ],
  "idle_temperature": [
    "100"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "5"
  ],
  "filament_retract_length_toolchange": [
    "20"
  ],
  "renamed_from": [
    "Filatech HIPS @PG"
  ],
  "name": "Filatech HIPS @XL",
  "type": "filament"
}