*ABSPG*
Unknown · OTHER
· by flsun-system
· 0 downloads
Inherited from this (4)
Settings
Flow
- Max volumetric speed (mm³/s)
-
12 overridden
Other settings
- compatible printers condition
-
printer_notes=~/.*MK4.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 overridden
- filament cooling final speed
-
50 overridden
- filament cooling initial speed
-
10 overridden
- filament cooling moves
-
5 overridden
- filament load time
-
15 overridden
- filament loading speed
-
14 overridden
- filament loading speed start
-
19 overridden
- filament minimal purge on wipe tower
-
35 overridden
- filament ramming parameters
-
120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6, overridden
- filament unload time
-
12 overridden
- filament unloading speed
-
20 overridden
- idle temperature
-
100 overridden
- start filament gcode
-
M900 K{if nozzle_diameter[0]==0.4}0.04{elsif nozzle_diameter[0]==0.25}0.1{elsif nozzle_diameter[0]==0.3}0.06{elsif nozzle_diameter[0]==0.35}0.05{elsif nozzle_diameter[0]==0.5}0.03{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.01{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif} M142 S40 ; set heatbreak target temp overridden
Raw resolved JSON
{
"idle_temperature": [
"100"
],
"filament_load_time": [
"15"
],
"filament_unload_time": [
"12"
],
"start_filament_gcode": [
"M900 K{if nozzle_diameter[0]==0.4}0.04{elsif nozzle_diameter[0]==0.25}0.1{elsif nozzle_diameter[0]==0.3}0.06{elsif nozzle_diameter[0]==0.35}0.05{elsif nozzle_diameter[0]==0.5}0.03{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.01{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S40 ; set heatbreak target temp"
],
"filament_cooling_moves": [
"5"
],
"filament_loading_speed": [
"14"
],
"filament_unloading_speed": [
"20"
],
"filament_ramming_parameters": [
"120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6",
""
],
"filament_cooling_final_speed": [
"50"
],
"filament_loading_speed_start": [
"19"
],
"compatible_printers_condition": [
"printer_notes=~/.*MK4.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8"
],
"filament_max_volumetric_speed": [
"12"
],
"filament_cooling_initial_speed": [
"10"
],
"filament_minimal_purge_on_wipe_tower": [
"35"
],
"name": "*ABSPG*",
"filament_settings_id": [
"*ABSPG*"
],
"type": "filament"
}