Generic PETG@Q2-Series

Generic · PETG · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_q_common

→

Generic PETG@Q2-Series

Inherited from this (4)

Settings

Basic information

Material variant: PETG overridden
was PLA (inherited)
Vendor: Generic overridden
was QIDI (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 1.24 (inherited)
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 245 overridden
was 210 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 210 (inherited)
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 40 overridden
was 100 (inherited)
Fan maximum (%): 90 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 60 (inherited)
Slow down if layer below (sec): 12 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.95 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 24.5 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	80 overridden was 60	80 overridden was 60
Cool Plate SuperTack	70 overridden	70 overridden

Other settings

activate air filtration: 1 inherited
additional cooling fan speed: 0 inherited
additional cooling fan speed unseal: 0 inherited
bed type: Cool Plate inherited
box temperature: 0 inherited
box temperature range high: 45 overridden
was 0 (inherited)
box temperature range low: 0 inherited
complete print exhaust fan speed: 0 inherited
dont slow down outer wall: 0 inherited
during print exhaust fan speed: 100 inherited
enable pressure advance: 1 inherited
filament adhesiveness category: 300 overridden
filament dev ams drying ams limitations: 1 inherited
filament dev ams drying heat distortion temperature: 45.0 inherited
filament dev ams drying temperature: 40.0, 40.0, 40.0, 40.0 inherited
filament dev ams drying time: 8.0, 8.0, 8.0, 8.0 inherited
filament dev chamber drying bed temperature: 90.0 inherited
filament dev chamber drying time: 12.0 inherited
filament dev drying cooling temperature: 35.0 inherited
filament dev drying softening temperature: 40.0 inherited
filament flush temp: 0 inherited
filament flush volumetric speed: 0 inherited
filament id: QD_1_0_41 overridden
filament long retractions when ec: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0 inherited
filament ramming travel time: 0 inherited
filament ramming volumetric speed: -1 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when ec: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament tower interface pre extrusion dist: 10 inherited
filament tower interface pre extrusion length: 0 inherited
filament tower interface print temp: -1 inherited
filament tower interface purge volume: 20 inherited
filament tower ironing area: 4 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 270 overridden
nozzle temperature range low: 220 overridden
overhang fan speed: 90 overridden
was 100 (inherited)
overhang fan threshold: 10% overridden
was 95% (inherited)
pressure advance: 0.056 overridden
was 0.042 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSG99 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 70 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "box_temperature": [
    "0"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.056"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "chamber_temperature": [
    "0"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_flush_temp": [
    "0"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament start gcode"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "box_temperature_range_low": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "box_temperature_range_high": [
    "45"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "filament_tower_ironing_area": [
    "4"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_dev_ams_drying_time": [
    "8.0",
    "8.0",
    "8.0",
    "8.0"
  ],
  "filament_ramming_travel_time": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "during_print_exhaust_fan_speed": [
    "100"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_flush_volumetric_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_dev_chamber_drying_time": [
    "12.0"
  ],
  "filament_pre_cooling_temperature": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "filament_long_retractions_when_ec": [
    "nil"
  ],
  "filament_ramming_volumetric_speed": [
    "-1"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "additional_cooling_fan_speed_unseal": [
    "0"
  ],
  "filament_dev_ams_drying_temperature": [
    "40.0",
    "40.0",
    "40.0",
    "40.0"
  ],
  "filament_tower_interface_print_temp": [
    "-1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_ec": [
    "nil"
  ],
  "filament_tower_interface_purge_volume": [
    "20"
  ],
  "filament_dev_ams_drying_ams_limitations": [
    "1"
  ],
  "filament_dev_drying_cooling_temperature": [
    "35.0"
  ],
  "filament_dev_drying_softening_temperature": [
    "40.0"
  ],
  "filament_dev_chamber_drying_bed_temperature": [
    "90.0"
  ],
  "filament_tower_interface_pre_extrusion_dist": [
    "10"
  ],
  "filament_tower_interface_pre_extrusion_length": [
    "0"
  ],
  "filament_dev_ams_drying_heat_distortion_temperature": [
    "45.0"
  ],
  "setting_id": "GFSG99",
  "filament_id": "QD_1_0_41",
  "compatible_printers": [],
  "supertack_plate_temp": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "filament_adhesiveness_category": [
    "300"
  ],
  "supertack_plate_temp_initial_layer": [
    "70"
  ],
  "name": "Generic PETG@Q2-Series"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:37