Generic PLA Silk @PGIS 0.6

Generic · PLA · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Generic PLA Silk @PGIS

→

Generic PLA Silk @PGIS 0.6

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*PLAPG*

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 25.4 inherited

Print temperature

Nozzle (initial layer) (°C): 230 inherited
Nozzle (other layers) (°C): 215 overridden
was 225 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 15 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 9 overridden
was 7 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	55 inherited	60 inherited

Other settings

bridge fan speed: 100 inherited
compatible printers condition: printer_notes=~/.*PG.*/ and printer_notes=~/.*MK4IS.*/ and nozzle_diameter[0]==0.6 overridden
was printer_notes=~/.*PG.*/ and printer_notes=~/.*MK4IS.*/ and nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6 (inherited)
cooling: 1 inherited
fan always on: 1 inherited
filament colour: #FFF0E0 inherited
filament cooling final speed: 2 via *PLAPG*
filament cooling initial speed: 3 via *PLAPG*
filament cooling moves: 1 via *PLAPG*
filament load time: 15 via *PLAPG*
filament loading speed: 14 via *PLAPG*
filament loading speed start: 19 via *PLAPG*
filament minimal purge on wipe tower: 15 via *PLAPG*
filament ramming parameters: 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6 via *PLAPG*
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 12 via *PLAPG*
filament unloading speed: 20 via *PLAPG*
filament unloading speed start: 100 via *PLAPG*
full fan speed layer: 3 via *PLAPG*
idle temperature: 70 via *PLAPG*
renamed from: Generic PLA Silk @MK4IS inherited
start filament gcode: M900 K{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.07{elsif nozzle_diameter[0]==0.35}0.06{elsif nozzle_diameter[0]==0.6}0.03{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.8}0.015{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.035{elsif nozzle_diameter[0]==0.5}0.022{elsif nozzle_diameter[0]==0.6}0.018{elsif nozzle_diameter[0]==0.8}0.012{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.075{else}0{endif} ; Filament gcode {endif} M142 S36 ; set heatbreak target temp inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "25.4"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "M900 K{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.07{elsif nozzle_diameter[0]==0.35}0.06{elsif nozzle_diameter[0]==0.6}0.03{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.8}0.015{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.035{elsif nozzle_diameter[0]==0.5}0.022{elsif nozzle_diameter[0]==0.6}0.018{elsif nozzle_diameter[0]==0.8}0.012{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.075{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "1"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "2"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PG.*/ and printer_notes=~/.*MK4IS.*/ and nozzle_diameter[0]==0.6"
  ],
  "filament_cooling_initial_speed": [
    "3"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_type": [
    "PLA"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_colour": [
    "#FFF0E0"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "215"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "filament_max_volumetric_speed": [
    "9"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "idle_temperature": [
    "70"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "renamed_from": [
    "Generic PLA Silk @MK4IS"
  ],
  "name": "Generic PLA Silk @PGIS 0.6",
  "type": "filament"
}