*PLAPG*
Unknown · OTHER
· by flsun-system
· 0 downloads
Inherited from this (2)
Settings
Cooling
- Slow down if layer below (sec)
-
8 overridden
Other settings
- compatible printers condition
-
printer_notes=~/.*MK4.*/ and nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6 overridden
- filament cooling final speed
-
2 overridden
- filament cooling initial speed
-
3 overridden
- filament cooling moves
-
1 overridden
- filament load time
-
15 overridden
- filament loading speed
-
14 overridden
- filament loading speed start
-
19 overridden
- filament minimal purge on wipe tower
-
15 overridden
- filament ramming parameters
-
130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6 overridden
- filament unload time
-
12 overridden
- filament unloading speed
-
20 overridden
- filament unloading speed start
-
100 overridden
- full fan speed layer
-
3 overridden
- idle temperature
-
70 overridden
- start filament gcode
-
M900 K{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.07{elsif nozzle_diameter[0]==0.35}0.06{elsif nozzle_diameter[0]==0.6}0.03{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.8}0.015{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.038{elsif nozzle_diameter[0]==0.5}0.025{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.014{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode {endif} M142 S36 ; set heatbreak target temp overridden
Raw resolved JSON
{
"idle_temperature": [
"70"
],
"filament_load_time": [
"15"
],
"filament_unload_time": [
"12"
],
"full_fan_speed_layer": [
"3"
],
"slow_down_layer_time": [
"8"
],
"start_filament_gcode": [
"M900 K{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.07{elsif nozzle_diameter[0]==0.35}0.06{elsif nozzle_diameter[0]==0.6}0.03{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.8}0.015{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.038{elsif nozzle_diameter[0]==0.5}0.025{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.014{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
],
"filament_cooling_moves": [
"1"
],
"filament_loading_speed": [
"14"
],
"filament_unloading_speed": [
"20"
],
"filament_ramming_parameters": [
"130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
],
"filament_cooling_final_speed": [
"2"
],
"filament_loading_speed_start": [
"19"
],
"compatible_printers_condition": [
"printer_notes=~/.*MK4.*/ and nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6"
],
"filament_cooling_initial_speed": [
"3"
],
"filament_unloading_speed_start": [
"100"
],
"filament_minimal_purge_on_wipe_tower": [
"15"
],
"name": "*PLAPG*",
"filament_settings_id": [
"*PLAPG*"
],
"type": "filament"
}