Generic TPU @RatRig

Generic · FLEX · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

Generic PLA @RatRig

→

Generic TPU @RatRig

Settings

Basic information

Material variant: FLEX overridden
was PLA (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.24 overridden
was 1.24 (inherited)
Cost (/kg): 20 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 205 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 195 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 2 overridden
was 2 (inherited)
Full fan if layer below (sec): 100 overridden
was 100 (inherited)
Slow down if layer below (sec): 8 overridden
was 15 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 0.89 overridden
was 0.89 (inherited)
Max volumetric speed (mm³/s): 5 overridden
was 0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	30 overridden was 68	30 overridden was 65

Other settings

bridge fan speed: 100 overridden
was 100 (inherited)
bridge internal fan speed: -1 overridden
cooling: 1 overridden
was 1 (inherited)
end filament gcode: ; Filament-specific end gcode ;END gcode for filament overridden
was ; Filament-specific end gcode ;END gcode for filament (inherited)
external perimeter fan speed: -1 overridden
fan always on: 1 overridden
was 1 (inherited)
filament colour: #FF00FF overridden
was #FF3232 (inherited)
filament cooling final speed: 3.4 overridden
was 3.4 (inherited)
filament cooling initial speed: 2.2 overridden
was 2.2 (inherited)
filament cooling moves: 4 overridden
was 4 (inherited)
filament cooling zone pause: 0 overridden
was 0 (inherited)
filament deretract speed: nil overridden
was nil (inherited)
filament dip extraction speed: 70 overridden
filament dip insertion speed: 33 overridden
filament enable toolchange part fan: 0 overridden
filament enable toolchange temp: 0 overridden
filament load time: 0 overridden
was 0 (inherited)
filament loading speed: 28 overridden
was 28 (inherited)
filament loading speed start: 3 overridden
was 3 (inherited)
filament max overlap: 100% overridden
filament max speed: 0 overridden
was 0 (inherited)
filament max wipe tower speed: 0 overridden
filament melt zone pause: 0 overridden
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament notes: This is a profile for TPU95A. It was tested with Anycubic TPU95A, but most of the economy TPU filaments behave pretty similar. You will want to optimize the temperature. Even different colors of the same brand can require 10° more or less. If you experience clogs or grinding, reduce the maximum volumetric speed! overridden
was — (inherited)
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
was 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 (inherited)
filament retract before travel: nil overridden
filament retract before wipe: nil overridden
filament retract layer change: nil overridden
filament retract length: 1 overridden
was 0.6 (inherited)
filament retract lift: 0.1 overridden
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract restart extra: nil overridden
filament retract speed: nil overridden
filament seam gap: nil overridden
filament shrink: 100% overridden
filament skinnydip distance: 31 overridden
filament soluble: 0 overridden
was 0 (inherited)
filament spool weight: 0 overridden
was 0 (inherited)
filament toolchange delay: 0 overridden
was 0 (inherited)
filament toolchange part fan speed: 50 overridden
filament toolchange temp: 200 overridden
filament unload time: 0 overridden
was 0 (inherited)
filament unloading speed: 90 overridden
was 90 (inherited)
filament unloading speed start: 100 overridden
was 100 (inherited)
filament use fast skinnydip: 0 overridden
filament use skinnydip: 0 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe advanced pigment: 0.5 overridden
filament wipe extra perimeter: nil overridden
filament wipe only crossing: nil overridden
filament wipe speed: nil overridden
full fan speed layer: 4 overridden
was 4 (inherited)
max speed reduction: 95% overridden
start filament gcode: ; Filament gcode SET_GCODE_OFFSET Z=0 SET_PRESSURE_ADVANCE ADVANCE=0.1 overridden
was ; Filament gcode SET_GCODE_OFFSET Z=0 SET_PRESSURE_ADVANCE ADVANCE=0.05 (inherited)
top fan speed: -1 overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_notes": [
    "This is a profile for TPU95A. It was tested with Anycubic TPU95A, but most of the economy TPU filaments behave pretty similar.\n\nYou will want to optimize the temperature. Even different colors of the same brand can require 10\u00b0 more or less.\n\nIf you experience clogs or grinding, reduce the maximum volumetric speed!"
  ],
  "hot_plate_temp": [
    "30"
  ],
  "filament_colour": [
    "#FF00FF"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament\n"
  ],
  "filament_load_time": [
    "0"
  ],
  "filament_max_speed": [
    "0"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "filament_flow_ratio": [
    "0.89"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_unload_time": [
    "0"
  ],
  "full_fan_speed_layer": [
    "4"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "start_filament_gcode": [
    "; Filament gcode\nSET_GCODE_OFFSET Z=0\nSET_PRESSURE_ADVANCE ADVANCE=0.1"
  ],
  "filament_spool_weight": [
    "0"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_retract_length": [
    "1"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_cooling_zone_pause": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "5"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "top_fan_speed": [
    "-1"
  ],
  "filament_shrink": [
    "100%"
  ],
  "compatible_prints": [
    ""
  ],
  "filament_seam_gap": [
    "nil"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_wipe_speed": [
    "nil"
  ],
  "max_speed_reduction": [
    "95%"
  ],
  "filament_max_overlap": [
    "100%"
  ],
  "filament_retract_lift": [
    "0.1"
  ],
  "filament_retract_speed": [
    "nil"
  ],
  "filament_use_skinnydip": [
    "0"
  ],
  "filament_melt_zone_pause": [
    "0"
  ],
  "filament_toolchange_temp": [
    "200"
  ],
  "bridge_internal_fan_speed": [
    "-1"
  ],
  "filament_custom_variables": [
    ""
  ],
  "compatible_prints_condition": [
    ""
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_skinnydip_distance": [
    "31"
  ],
  "filament_use_fast_skinnydip": [
    "0"
  ],
  "filament_wipe_only_crossing": [
    "nil"
  ],
  "external_perimeter_fan_speed": [
    "-1"
  ],
  "filament_dip_insertion_speed": [
    "33"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "compatible_printers_condition": [
    ""
  ],
  "filament_dip_extraction_speed": [
    "70"
  ],
  "filament_max_wipe_tower_speed": [
    "0"
  ],
  "filament_retract_layer_change": [
    "nil"
  ],
  "filament_wipe_extra_perimeter": [
    "nil"
  ],
  "filament_retract_before_travel": [
    "nil"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_wipe_advanced_pigment": [
    "0.5"
  ],
  "filament_enable_toolchange_temp": [
    "0"
  ],
  "filament_toolchange_part_fan_speed": [
    "50"
  ],
  "filament_enable_toolchange_part_fan": [
    "0"
  ],
  "name": "Generic TPU @RatRig",
  "filament_settings_id": [
    "Generic TPU @RatRig"
  ],
  "type": "filament"
}