Generic PLA @RatRig

Generic · PLA · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inherited from this (1)

Generic TPU @RatRig

Settings

Basic information

Material variant: PLA overridden
Vendor: Generic overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 1.24 overridden
Cost (/kg): 20 overridden

Print temperature

Nozzle (initial layer) (°C): 205 overridden
Nozzle (other layers) (°C): 195 overridden

Cooling

Fan minimum (%): 100 overridden
Fan maximum (%): 100 overridden
Disable fan for first N layers: 2 overridden
Full fan if layer below (sec): 100 overridden
Slow down if layer below (sec): 15 overridden
Min speed when slowed (mm/s): 10 overridden

Flow

Flow ratio: 0.89 overridden
Max volumetric speed (mm³/s): 0 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	68 overridden	65 overridden

Other settings

bridge fan speed: 100 overridden
cooling: 1 overridden
end filament gcode: ; Filament-specific end gcode ;END gcode for filament overridden
fan always on: 1 overridden
filament colour: #FF3232 overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament cooling zone pause: 0 overridden
filament deretract speed: nil overridden
filament load time: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament max speed: 0 overridden
filament minimal purge on wipe tower: 15 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract length: 0.6 overridden
filament soluble: 0 overridden
filament spool weight: 0 overridden
filament toolchange delay: 0 overridden
filament unload time: 0 overridden
filament unloading speed: 90 overridden
filament unloading speed start: 100 overridden
filament wipe: nil overridden
full fan speed layer: 4 overridden
start filament gcode: ; Filament gcode SET_GCODE_OFFSET Z=0 SET_PRESSURE_ADVANCE ADVANCE=0.05 overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_notes": [
    ""
  ],
  "hot_plate_temp": [
    "65"
  ],
  "filament_colour": [
    "#FF3232"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament\n"
  ],
  "filament_load_time": [
    "0"
  ],
  "filament_max_speed": [
    "0"
  ],
  "nozzle_temperature": [
    "195"
  ],
  "filament_flow_ratio": [
    "0.89"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_unload_time": [
    "0"
  ],
  "full_fan_speed_layer": [
    "4"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "; Filament gcode\nSET_GCODE_OFFSET Z=0\nSET_PRESSURE_ADVANCE ADVANCE=0.05"
  ],
  "filament_spool_weight": [
    "0"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_retract_length": [
    "0.6"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_cooling_zone_pause": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "68"
  ],
  "filament_max_volumetric_speed": [
    "0"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "205"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "name": "Generic PLA @RatRig",
  "filament_settings_id": [
    "Generic PLA @RatRig"
  ],
  "type": "filament"
}