PA_S1flsunq

Unknown · PA · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_flsunq*

→

*PA_S1flsunq*

Inherited from this (1)

Generic PA_S1 @FLSUN

Settings

Basic information

Material variant: PA overridden
was PLA (inherited)
Vendor: (Unknown) inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.26 overridden
was 0 (inherited)
Cost (/kg): 0 overridden
was 60 (inherited)

Print temperature

Nozzle (initial layer) (°C): 290 overridden
Nozzle (other layers) (°C): 280 overridden

Cooling

Fan minimum (%): 50 overridden
Fan maximum (%): 50 overridden
Disable fan for first N layers: 1 overridden
was 1 (inherited)
Full fan if layer below (sec): 1 overridden
Slow down if layer below (sec): 4 overridden
was 15 (inherited)
Min speed when slowed (mm/s): 20 overridden

Flow

Flow ratio: 1.1 overridden
was 0.95 (inherited)
Max volumetric speed (mm³/s): 20 overridden
was 0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 overridden	100 overridden

Other settings

bottom solid fill flow: 1 overridden
was 0.9 (inherited)
bridge fan speed: 25 overridden
compatible printers condition: printer_model=="S1" and nozzle_diameter[0]==0.4 overridden
cooling: 1 inherited
enable dynamic fan speeds: 0 inherited
end filament gcode: ; Filament-specific end gcode ;END gcode for filament inherited
external wall flow: 1.05 inherited
fan always on: 1 overridden
was 1 (inherited)
filament colour: #15a95d inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament deretract speed: nil overridden
was nil (inherited)
filament estimated empty distance: 30 overridden
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 30 overridden
was 15 (inherited)
filament multitool ramming: 0 inherited
filament multitool ramming flow: 10 inherited
filament multitool ramming volume: 10 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: nil overridden
was 2 (inherited)
filament retract before wipe: nil inherited
filament retract layer change: nil overridden
was 0 (inherited)
filament retract length: nil overridden
was 0.8 (inherited)
filament retract length toolchange: nil inherited
filament retract lift: nil inherited
filament retract lift above: nil inherited
filament retract lift below: nil inherited
filament retract restart extra: nil overridden
was -0.1 (inherited)
filament retract restart extra toolchange: nil inherited
filament retract speed: nil overridden
was 40 (inherited)
filament soluble: 0 inherited
filament spool weight: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil overridden
was 0 (inherited)
first flow: 1.1 overridden
full fan speed layer: 3 overridden
was 5 (inherited)
idle temperature: nil inherited
overhang fan speed 0: 30 overridden
overhang fan speed 1: 70 overridden
overhang fan speed 2: 80 overridden
overhang fan speed 3: 90 overridden
start filament gcode: ; Filament gcode inherited
top fan speed: 0 overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#15a95d"
  ],
  "filament_vendor": [
    "(Unknown)"
  ],
  "filament_density": [
    "1.26"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "nil"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament\n"
  ],
  "external_wall_flow": [
    "1.05"
  ],
  "filament_load_time": [
    "0"
  ],
  "filament_flow_ratio": [
    "1.1"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "start_filament_gcode": [
    "; Filament gcode\n"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "filament_spool_weight": [
    "0"
  ],
  "bottom_solid_fill_flow": [
    "1"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_retract_speed": [
    "nil"
  ],
  "filament_retract_length": [
    "nil"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "enable_dynamic_fan_speeds": [
    "0"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "filament_retract_layer_change": [
    "nil"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_before_travel": [
    "nil"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_retract_length_toolchange": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "30"
  ],
  "filament_retract_restart_extra_toolchange": [
    "nil"
  ],
  "first_flow": [
    "1.1"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "50"
  ],
  "top_fan_speed": [
    "0"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "bridge_fan_speed": [
    "25"
  ],
  "nozzle_temperature": [
    "280"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "overhang_fan_speed_0": [
    "30"
  ],
  "overhang_fan_speed_1": [
    "70"
  ],
  "overhang_fan_speed_2": [
    "80"
  ],
  "overhang_fan_speed_3": [
    "90"
  ],
  "fan_cooling_layer_time": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "compatible_printers_condition": [
    "printer_model==\"S1\" and nozzle_diameter[0]==0.4"
  ],
  "nozzle_temperature_initial_layer": [
    "290"
  ],
  "filament_estimated_empty_distance": [
    "30"
  ],
  "name": "*PA_S1flsunq*",
  "type": "filament"
}