common_flsunq

Unknown · PLA · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inherited from this (33)

View all 33 →

Settings

Basic information

Material variant: PLA overridden
Vendor: (Unknown) overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 0 overridden
Cost (/kg): 60 overridden

Cooling

Disable fan for first N layers: 1 overridden
Slow down if layer below (sec): 15 overridden

Flow

Flow ratio: 0.95 overridden
Max volumetric speed (mm³/s): 0 overridden

Other settings

bottom solid fill flow: 0.9 overridden
cooling: 1 overridden
enable dynamic fan speeds: 0 overridden
end filament gcode: ; Filament-specific end gcode ;END gcode for filament overridden
external wall flow: 1.05 overridden
fan always on: 1 overridden
filament colour: #15a95d overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament deretract speed: nil overridden
filament load time: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament minimal purge on wipe tower: 15 overridden
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract before travel: 2 overridden
filament retract before wipe: nil overridden
filament retract layer change: 0 overridden
filament retract length: 0.8 overridden
filament retract length toolchange: nil overridden
filament retract lift: nil overridden
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract restart extra: -0.1 overridden
filament retract restart extra toolchange: nil overridden
filament retract speed: 40 overridden
filament soluble: 0 overridden
filament spool weight: 0 overridden
filament toolchange delay: 0 overridden
filament unload time: 0 overridden
filament unloading speed: 90 overridden
filament unloading speed start: 100 overridden
filament wipe: 0 overridden
full fan speed layer: 5 overridden
idle temperature: nil overridden
start filament gcode: ; Filament gcode overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "1"
  ],
  "filament_cost": [
    "60"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#15a95d"
  ],
  "filament_vendor": [
    "(Unknown)"
  ],
  "filament_density": [
    "0"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "nil"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament\n"
  ],
  "external_wall_flow": [
    "1.05"
  ],
  "filament_load_time": [
    "0"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "full_fan_speed_layer": [
    "5"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "; Filament gcode\n"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "filament_spool_weight": [
    "0"
  ],
  "bottom_solid_fill_flow": [
    "0.9"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_retract_speed": [
    "40"
  ],
  "filament_retract_length": [
    "0.8"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "enable_dynamic_fan_speeds": [
    "0"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "filament_max_volumetric_speed": [
    "0"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "filament_retract_restart_extra": [
    "-0.1"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_retract_length_toolchange": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_restart_extra_toolchange": [
    "nil"
  ],
  "name": "*common_flsunq*",
  "type": "filament"
}