ColorFabb nGen flex @Caribou

ColorFabb · FLEX · by super-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_Caribou*

→

*FLEX_Caribou*

→

ColorFabb nGen flex @Caribou

Settings

Basic information

Material variant: FLEX inherited
Vendor: ColorFabb overridden
Diameter (mm): 1.75 inherited
Density (g/cm³): 1 overridden
was 0 (inherited)
Cost (/kg): 58.30 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 60 (inherited)
Fan maximum (%): 35 overridden
was 90 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 10 overridden
was 100 (inherited)
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.95 overridden
was 1.10 (inherited)
Max volumetric speed (mm³/s): 5 overridden
was 1.5 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	85 overridden was 50	85 overridden was 50

Other settings

bridge fan speed: 40 overridden
was 80 (inherited)
compatible printers condition: nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_CARIBOU3D.*/ and printer_notes=~/.*PRINTER_MODEL_(MK3S|MK3KLIPPER|DUET).*/ and single_extruder_multi_material) overridden
was nozzle_diameter[0]>0.35 and num_extruders==1 && ! (printer_notes=~/.*PRINTER_VENDOR_CARIBOU3D.*/ and printer_notes=~/.*PRINTER_MODEL_(MK3S|MK3KLIPPER|DUET).*/ and single_extruder_multi_material) (inherited)
cooling: 1 overridden
was 0 (inherited)
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #008000 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament deretract speed: 25 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract length: nil overridden
was 0.8 (inherited)
filament retract lift: 0 overridden
was 0 (inherited)
filament soluble: 0 inherited
filament spool weight: 236 overridden
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: 0 inherited
start filament gcode: {if printer_notes=~/.*PRINTER_MODEL_MK3S.*/}M900 K0, Filament gcode{endif}" inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "58.30"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "{if printer_notes=~/.*PRINTER_MODEL_MK3S.*/}M900 K0",
    "Filament gcode{endif}\""
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]>0.35 and ! (printer_notes=~/.*PRINTER_VENDOR_CARIBOU3D.*/ and printer_notes=~/.*PRINTER_MODEL_(MK3S|MK3KLIPPER|DUET).*/ and single_extruder_multi_material)"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "35"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": [
    "0"
  ],
  "hot_plate_temp": [
    "85"
  ],
  "filament_colour": [
    "#008000"
  ],
  "bridge_fan_speed": [
    "40"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "filament_retract_lift": [
    "0"
  ],
  "fan_cooling_layer_time": [
    "10"
  ],
  "filament_retract_length": [
    "nil"
  ],
  "filament_deretract_speed": [
    "25"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "85"
  ],
  "filament_max_volumetric_speed": [
    "5"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "filament_vendor": [
    "ColorFabb"
  ],
  "filament_spool_weight": [
    "236"
  ],
  "name": "ColorFabb nGen flex @Caribou",
  "type": "filament"
}