common_Caribou

Unknown · OTHER · by super-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inherited from this (6)

Settings

Basic information

Diameter (mm): 1.75 overridden
Density (g/cm³): 0 overridden
Cost (/kg): 0 overridden

Cooling

Slow down if layer below (sec): 15 overridden
Min speed when slowed (mm/s): 15 overridden

Flow

Flow ratio: 0.95 overridden

Other settings

compatible printers condition: ! (printer_notes=~/.*PRINTER_VENDOR_CARIBOU3D.*/ and printer_notes=~/.*PRINTER_MODEL_(MK3S|MK3KLIPPER|DUET).*/ and single_extruder_multi_material) overridden
cooling: 1 overridden
end filament gcode: ; Filament-specific end gcode overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament load time: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament minimal purge on wipe tower: 15 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament soluble: 0 overridden
filament toolchange delay: 0 overridden
filament unload time: 0 overridden
filament unloading speed: 90 overridden
filament unloading speed start: 100 overridden
start filament gcode: {if printer_notes=~/.*PRINTER_MODEL_MK3S.*/}M900 K30 ; Filament gcode {endif} overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "0"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "{if printer_notes=~/.*PRINTER_MODEL_MK3S.*/}M900 K30 ; Filament gcode {endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "! (printer_notes=~/.*PRINTER_VENDOR_CARIBOU3D.*/ and printer_notes=~/.*PRINTER_MODEL_(MK3S|MK3KLIPPER|DUET).*/ and single_extruder_multi_material)"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "name": "*common_Caribou*",
  "type": "filament"
}