PET_Caribou

Unknown · PETG · by super-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_Caribou*

→

*PET_Caribou*

Inherited from this (12)

View all 12 →

Settings

Basic information

Material variant: PETG overridden
Diameter (mm): 1.75 inherited
Density (g/cm³): 0 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 230 overridden
Nozzle (other layers) (°C): 240 overridden

Cooling

Fan minimum (%): 30 overridden
Fan maximum (%): 50 overridden
Disable fan for first N layers: 3 overridden
Full fan if layer below (sec): 20 overridden
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 8 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	85 overridden	90 overridden

Other settings

bridge fan speed: 50 overridden
compatible printers condition: ! (printer_notes=~/.*PRINTER_VENDOR_CARIBOU3D.*/ and printer_notes=~/.*PRINTER_MODEL_(MK3S|MK3KLIPPER|DUET).*/ and single_extruder_multi_material) overridden
was ! (printer_notes=~/.*PRINTER_VENDOR_CARIBOU3D.*/ and printer_notes=~/.*PRINTER_MODEL_(MK3S|MK3KLIPPER|DUET).*/ and single_extruder_multi_material) (inherited)
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 overridden
filament colour: #FF8000 overridden
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract length: 0.6 overridden
filament retract lift: 0.2 overridden
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
full fan speed layer: 5 overridden
start filament gcode: {if printer_notes=~/.*PRINTER_MODEL_MK3S.*/}M900 K{if nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5 {if nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0{endif} overridden
was {if printer_notes=~/.*PRINTER_MODEL_MK3S.*/}M900 K30 ; Filament gcode {endif} (inherited)

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "0"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "{if printer_notes=~/.*PRINTER_MODEL_MK3S.*/}M900 K{if nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "! (printer_notes=~/.*PRINTER_VENDOR_CARIBOU3D.*/ and printer_notes=~/.*PRINTER_MODEL_(MK3S|MK3KLIPPER|DUET).*/ and single_extruder_multi_material)"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "filament_colour": [
    "#FF8000"
  ],
  "bridge_fan_speed": [
    "50"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "full_fan_speed_layer": [
    "5"
  ],
  "filament_retract_lift": [
    "0.2"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_retract_length": [
    "0.6"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "85"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "name": "*PET_Caribou*",
  "type": "filament"
}