Polymaker PA6-CF20 @base

Phrozen · PA6-CF · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Fiberon PA6-CF @base

→

Fiberon PA6-CF @System

→

Polymaker PA6-CF20 @base

Inherited from this (1)

Polymaker PA6-CF20 @System

Settings

Basic information

Material variant: PA6-CF inherited
Vendor: Phrozen overridden
was Polymaker (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.17 inherited
Cost (/kg): 83.99 inherited

Print temperature

Nozzle (initial layer) (°C): 300 inherited
Nozzle (other layers) (°C): 300 inherited

Cooling

Fan minimum (%): 10 overridden
was 0 (inherited)
Fan maximum (%): 30 overridden
was 100 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 overridden
was 15 (inherited)
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.97 overridden
was 0.95 (inherited)
Max volumetric speed (mm³/s): 12 inherited

Retraction

Retraction length (mm): 3 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 overridden was 0	50 overridden was 0
Textured Cool Plate	50 overridden	50 overridden
Engineering Plate	50 overridden was 40	50 overridden was 40
High Temp Plate	50 overridden was 40	50 overridden was 40
Textured PEI Plate	50 overridden was 40	50 overridden was 40
Cool Plate SuperTack	50 overridden was 45	50 overridden was 45

Other settings

activate air filtration: 0 inherited
chamber temperatures: 0 inherited
complete print exhaust fan speed: 70 inherited
during print exhaust fan speed: 70 inherited
enable pressure advance: 1 overridden
filament id: OGFL50 inherited
filament is support: 0 inherited
filament long retractions when cut: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil inherited
filament retraction minimum travel: nil inherited
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: Normal Lift overridden
was nil (inherited)
full fan speed layer: 0 inherited
instantiation: false overridden
was true (inherited)
nozzle temperature range high: 300 inherited
nozzle temperature range low: 280 inherited
overhang fan speed: 80 overridden
was 100 (inherited)
overhang fan threshold: 50% overridden
was 95% (inherited)
pressure advance: 0.035 overridden
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: PRZ007 overridden
was OGFSL50_00 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 215 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "83.99"
  ],
  "filament_type": [
    "PA6-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Phrozen"
  ],
  "filament_density": [
    "1.17"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "300"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "0.97"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    "Polymaker PA6-CF20"
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "Normal Lift"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "supertack_plate_temp": [
    "50"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "215"
  ],
  "filament_retraction_length": [
    "3"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "300"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "50"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "280"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "filament_id": "OGFL50",
  "setting_id": "PRZ007",
  "pressure_advance": [
    "0.035"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "textured_cool_plate_temp": [
    "50"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "50"
  ],
  "name": "Polymaker PA6-CF20 @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:23