fdm_filament_common

Generic · PLA · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inherited from this (19)

View all 19 →

Settings

Basic information

Material variant: PLA overridden
Vendor: Generic overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 0 overridden
Cost (/kg): 0 overridden

Print temperature

Nozzle (initial layer) (°C): 200 overridden
Nozzle (other layers) (°C): 200 overridden

Cooling

Fan minimum (%): 35 overridden
Fan maximum (%): 100 overridden
Disable fan for first N layers: 3 overridden
Full fan if layer below (sec): 60 overridden
Slow down if layer below (sec): 8 overridden
Min speed when slowed (mm/s): 10 overridden

Flow

Flow ratio: 1 overridden
Max volumetric speed (mm³/s): 0 overridden

Retraction

Retraction length (mm): nil overridden
Retraction speed (mm/s): nil overridden
Deretraction speed (mm/s): nil overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden	60 overridden
Engineering Plate	60 overridden	60 overridden
High Temp Plate	60 overridden	60 overridden
Textured PEI Plate	60 overridden	60 overridden
Cool Plate SuperTack	45 overridden	45 overridden

Other settings

activate air filtration: 0 overridden
chamber temperatures: 0 overridden
complete print exhaust fan speed: 70 overridden
during print exhaust fan speed: 70 overridden
filament is support: 0 overridden
filament long retractions when cut: nil overridden
filament minimal purge on wipe tower: 15 overridden
filament retract before wipe: nil overridden
filament retract restart extra: nil overridden
filament retract when changing layer: nil overridden
filament retraction distances when cut: nil overridden
filament retraction minimum travel: nil overridden
filament scarf gap: 0% overridden
filament scarf height: 10% overridden
filament scarf length: 10 overridden
filament scarf seam type: none overridden
filament shrink: 100% overridden
filament soluble: 0 overridden
filament wipe: nil overridden
filament wipe distance: nil overridden
filament z hop: nil overridden
filament z hop types: nil overridden
full fan speed layer: 0 overridden
instantiation: false overridden
overhang fan speed: 100 overridden
overhang fan threshold: 95% overridden
reduce fan stop start freq: 0 overridden
required nozzle HRC: 3 overridden
slow down for layer cooling: 1 overridden
temperature vitrification: 100 overridden

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "35"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "0"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "200"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "supertack_plate_temp": [
    "45"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "0"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "200"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "45"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "name": "fdm_filament_common"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 13:21
v1 created 2026-05-19 13:21