fdm_filament_pctg

Generic · PCTG · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pctg

Inherited from this (1)

Generic PCTG @System

Settings

Basic information

Material variant: PCTG overridden
was PLA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 0 (inherited)
Cost (/kg): 30 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 255 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 255 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 35 (inherited)
Fan maximum (%): 100 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 20 overridden
was 60 (inherited)
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 12 overridden
was 0 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	0 overridden was 60	0 overridden was 60
High Temp Plate	80 overridden was 60	80 overridden was 60
Textured PEI Plate	80 overridden was 60	80 overridden was 60
Cool Plate SuperTack	0 overridden was 45	0 overridden was 45

Other settings

activate air filtration: 0 inherited
chamber temperatures: 0 inherited
complete print exhaust fan speed: 70 inherited
during print exhaust fan speed: 70 inherited
filament id: OGFG97 overridden
filament is support: 0 inherited
filament long retractions when cut: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil inherited
filament retraction minimum travel: nil inherited
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 260 overridden
nozzle temperature range low: 220 overridden
overhang fan speed: 100 inherited
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 overridden
was 0 (inherited)
required nozzle HRC: 3 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 70 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PCTG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "textured_plate_temp_initial_layer": [
    "80"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "filament_id": "OGFG97",
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "name": "fdm_filament_pctg"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:21