Overture ABS Basic @base

Overture · ABS · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Overture ABS Basic @base

Inherited from this (1)

Overture ABS Basic @System

Settings

Basic information

Material variant: ABS overridden
was ABS (inherited)
Vendor: OVERTURE overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.15 overridden
was 1.04 (inherited)
Cost (/kg): 0 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 260 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 10 (inherited)
Fan maximum (%): 50 overridden
was 80 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 38 overridden
was 30 (inherited)
Slow down if layer below (sec): 2 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 16 overridden
was 28.6 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 105	0 overridden was 105
Engineering Plate	90 overridden was 105	90 overridden was 105
High Temp Plate	90 overridden was 105	90 overridden was 105
Textured PEI Plate	90 overridden was 60	90 overridden was 60
Cool Plate SuperTack	45 inherited	45 inherited

Custom G-code

filament_start_gcode overridden

; Filament gcode
{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

filament_end_gcode overridden

; filament end gcode 
M106 P3 S0

Other settings

activate air filtration: 1 overridden
was 0 (inherited)
additional cooling fan speed: 0 overridden
chamber temperatures: 0 overridden
was 0 (inherited)
complete print exhaust fan speed: 70 overridden
was 70 (inherited)
description: Overture ABS settings from https://overture3d.com/. overridden
during print exhaust fan speed: 70 overridden
was 70 (inherited)
enable overhang bridge fan: 1 overridden
enable pressure advance: 0 overridden
filament id: OVTABS08 overridden
filament is support: 0 overridden
was 0 (inherited)
filament long retractions when cut: nil overridden
was nil (inherited)
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament retract before wipe: nil overridden
was nil (inherited)
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction distances when cut: nil overridden
was nil (inherited)
filament retraction minimum travel: nil overridden
was nil (inherited)
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 overridden
was 0 (inherited)
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
instantiation: false overridden
was false (inherited)
is custom defined: 0 overridden
nozzle temperature range high: 265 overridden
was 270 (inherited)
nozzle temperature range low: 245 overridden
was 240 (inherited)
overhang fan speed: 100 overridden
was 80 (inherited)
overhang fan threshold: 95% overridden
was 25% (inherited)
pressure advance: 0.02 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 3 overridden
was 3 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 103 overridden
was 110 (inherited)
version: 1.9.0.14 overridden

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "90"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "OVERTURE"
  ],
  "filament_density": [
    "1.15"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \nM106 P3 S0\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "90"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    "OVERTURE ABS Basic"
  ],
  "filament_start_gcode": [
    "; Filament gcode\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "supertack_plate_temp": [
    "45"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "38"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "103"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "90"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "45"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "245"
  ],
  "nozzle_temperature_range_high": [
    "265"
  ],
  "version": "1.9.0.14",
  "description": "Overture ABS settings from https://overture3d.com/.",
  "filament_id": "OVTABS08",
  "filament_notes": "",
  "pressure_advance": [
    "0.02"
  ],
  "is_custom_defined": "0",
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "name": "Overture ABS Basic @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:22