Overture TPU @base

Overture · TPU · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Overture TPU @base

Inherited from this (1)

Overture TPU @System

Settings

Basic information

Material variant: TPU overridden
was TPU (inherited)
Vendor: OVERTURE overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.18 overridden
was 1.24 (inherited)
Cost (/kg): 0 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 120 overridden
was 100 (inherited)
Slow down if layer below (sec): 120 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 15 inherited

Retraction

Retraction length (mm): 0.4 overridden
was 0.4 (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 overridden was 30	35 overridden was 30
Engineering Plate	0 overridden was 30	0 overridden was 30
High Temp Plate	35 overridden was 35	35 overridden was 35
Textured PEI Plate	35 overridden was 60	35 overridden was 60
Cool Plate SuperTack	45 inherited	45 inherited

Custom G-code

filament_start_gcode overridden

; filament start gcode
{if  (bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S255
{elsif(bed_temperature[current_extruder] >30)||(bed_temperature_initial_layer[current_extruder] >30)}M106 P3 S180
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

filament_end_gcode overridden

; filament end gcode 
M106 P3 S0

Other settings

activate air filtration: 0 overridden
was 0 (inherited)
additional cooling fan speed: 100 overridden
was 70 (inherited)
chamber temperatures: 0 overridden
was 0 (inherited)
complete print exhaust fan speed: 70 overridden
was 70 (inherited)
description: Overture TPU settings from https://overture3d.com/. overridden
during print exhaust fan speed: 70 overridden
was 70 (inherited)
enable overhang bridge fan: 1 overridden
enable pressure advance: 0 overridden
filament id: OGFOVT08 overridden
filament is support: 0 overridden
was 0 (inherited)
filament long retractions when cut: nil overridden
was nil (inherited)
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament retract before wipe: nil overridden
was nil (inherited)
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction distances when cut: nil overridden
was nil (inherited)
filament retraction minimum travel: nil overridden
was nil (inherited)
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 overridden
was 0 (inherited)
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 230 overridden
was 250 (inherited)
nozzle temperature range low: 210 overridden
was 200 (inherited)
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 95% overridden
was 95% (inherited)
pressure advance: 0.02 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 3 overridden
was 3 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 0 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "35"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "OVERTURE"
  ],
  "filament_density": [
    "1.18"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \nM106 P3 S0\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "35"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if  (bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S255\n{elsif(bed_temperature[current_extruder] >30)||(bed_temperature_initial_layer[current_extruder] >30)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "120"
  ],
  "supertack_plate_temp": [
    "45"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "120"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "0"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "35"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "textured_plate_temp_initial_layer": [
    "35"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "45"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "description": "Overture TPU settings from https://overture3d.com/.",
  "filament_id": "OGFOVT08",
  "filament_notes": "",
  "pressure_advance": [
    "0.02"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "name": "Overture TPU @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:22