Phrozen ABS Basic @base

Phrozen · ABS · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Phrozen ABS Basic @base

Compatible printers (3)

Phrozen Arco 0.2 nozzle
Phrozen Arco 0.4 nozzle
Phrozen Arco 0.6 nozzle

Inherited from this (3)

Settings

Basic information

Material variant: ABS overridden
was ABS (inherited)
Vendor: Phrozen overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 overridden
was 1.04 (inherited)
Cost (/kg): 24.99 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 260 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 10 (inherited)
Fan maximum (%): 20 overridden
was 80 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 30 overridden
was 30 (inherited)
Slow down if layer below (sec): 12 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 16 overridden
was 28.6 (inherited)

Retraction

Retraction length (mm): 0.4 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 105	0 overridden was 105
Textured Cool Plate	0 overridden	0 overridden
Engineering Plate	100 overridden was 105	100 overridden was 105
High Temp Plate	100 overridden was 105	100 overridden was 105
Textured PEI Plate	100 overridden was 60	100 overridden was 60
Cool Plate SuperTack	0 overridden was 45	0 overridden was 45

Other settings

activate air filtration: 0 inherited
additional cooling fan speed: 0 overridden
chamber temperatures: 0 inherited
compatible printers: Phrozen Arco 0.2 nozzle, Phrozen Arco 0.4 nozzle, Phrozen Arco 0.6 nozzle overridden
was — (inherited)
complete print exhaust fan speed: 70 inherited
during print exhaust fan speed: 70 inherited
enable overhang bridge fan: 1 overridden
filament id: PRZD01 overridden
filament is support: 0 inherited
filament long retractions when cut: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil inherited
filament retraction minimum travel: nil inherited
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 overridden
was 0 (inherited)
idle temperature: 0 overridden
instantiation: false overridden
was false (inherited)
is custom defined: 0 overridden
nozzle temperature range high: 280 overridden
was 270 (inherited)
nozzle temperature range low: 240 overridden
was 240 (inherited)
overhang fan speed: 80 overridden
was 80 (inherited)
overhang fan threshold: 25% overridden
was 25% (inherited)
reduce fan stop start freq: 0 overridden
was 1 (inherited)
required nozzle HRC: 3 inherited
slow down for layer cooling: 1 inherited
slow down for layer cooling: 1 overridden
temperature vitrification: 100 overridden
was 110 (inherited)
version: 0 overridden

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Phrozen"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "compatible_printers": [
    "Phrozen Arco 0.2 nozzle",
    "Phrozen Arco 0.4 nozzle",
    "Phrozen Arco 0.6 nozzle"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    "Phrozen ABS Basic"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "version": "0",
  "filament_id": "PRZD01",
  "idle_temperature": [
    "0"
  ],
  "is_custom_defined": "0",
  "textured_cool_plate_temp": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "slow_down_for_layer_cooling ": [
    "1"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "0"
  ],
  "name": "Phrozen ABS Basic @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:22