Phrozen PLA Tough @base

Phrozen · PLA · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Phrozen PLA Tough @base

Inherited from this (4)

Settings

Basic information

Material variant: PLA inherited
Vendor: Phrozen overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.23 overridden
was 1.24 (inherited)
Cost (/kg): 20 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 210 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 210 overridden
was 220 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 overridden
was 1 (inherited)
Full fan if layer below (sec): 6 overridden
was 100 (inherited)
Slow down if layer below (sec): 0 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1.02 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 30 overridden
was 12 (inherited)

Retraction

Retraction length (mm): 0.6 overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 overridden was 35	35 overridden was 35
Textured Cool Plate	40 overridden	40 overridden
Engineering Plate	0 overridden was 0	0 overridden was 0
High Temp Plate	60 overridden was 45	60 overridden was 45
Textured PEI Plate	55 overridden was 60	55 overridden was 60
Cool Plate SuperTack	35 overridden was 45	35 overridden was 45

Custom G-code

filament_start_gcode overridden

; filament start gcode
{if  (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255
{elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

filament_end_gcode overridden

; filament end gcode 
M106 P3 S0

Other settings

activate air filtration: 0 overridden
was 0 (inherited)
activate chamber temp control: 0 overridden
adaptive pressure advance: 0 overridden
adaptive pressure advance bridges: 0 overridden
adaptive pressure advance model: 0,0,0 0,0,0 overridden
adaptive pressure advance overhangs: 0 overridden
additional cooling fan speed: 70 overridden
was 70 (inherited)
chamber temperatures: 0 inherited
complete print exhaust fan speed: 70 overridden
was 70 (inherited)
dont slow down outer wall: 1 overridden
during print exhaust fan speed: 70 overridden
was 70 (inherited)
enable overhang bridge fan: 1 overridden
enable pressure advance: 1 overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament id: PRZA07 overridden
filament is support: 0 overridden
was 0 (inherited)
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament long retractions when cut: nil overridden
was nil (inherited)
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction distances when cut: nil overridden
was nil (inherited)
filament retraction minimum travel: nil overridden
was nil (inherited)
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% overridden
was 100% (inherited)
filament shrinkage compensation z: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament stamping distance: 0 overridden
filament stamping loading speed: 0 overridden
filament toolchange delay: 0 overridden
filament unloading speed: 90 overridden
filament unloading speed start: 100 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: 0.4 overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
idle temperature: 0 overridden
instantiation: false overridden
was false (inherited)
internal bridge fan speed: -1 overridden
nozzle temperature range high: 230 overridden
was 230 (inherited)
nozzle temperature range low: 210 overridden
was 190 (inherited)
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 50% overridden
was 50% (inherited)
pellet flow coefficient: 0.4157 overridden
pressure advance: 0.03 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 3 overridden
was 3 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 60 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Phrozen"
  ],
  "filament_density": [
    "1.23"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \nM106 P3 S0\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "1.02"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "55"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    "Phrozen PLA Tough"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if  (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255\n{elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "0"
  ],
  "supertack_plate_temp": [
    "35"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "6"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0.6"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "30"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "textured_plate_temp_initial_layer": [
    "55"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "35"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "filament_id": "PRZA07",
  "filament_notes": [
    ""
  ],
  "idle_temperature": [
    "0"
  ],
  "pressure_advance": [
    "0.03"
  ],
  "chamber_temperature": [
    "0"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "pellet_flow_coefficient": [
    "0.4157"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "textured_cool_plate_temp": [
    "40"
  ],
  "adaptive_pressure_advance": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "1"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "internal_bridge_fan_speed": [
    "-1"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_stamping_distance": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "adaptive_pressure_advance_model": [
    "0,0,0\n0,0,0"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_stamping_loading_speed": [
    "0"
  ],
  "adaptive_pressure_advance_bridges": [
    "0"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_shrinkage_compensation_z": [
    "100%"
  ],
  "adaptive_pressure_advance_overhangs": [
    "0"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "40"
  ],
  "name": "Phrozen PLA Tough @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:21