AliZ PA-CF @base

Aliz · PA-CF · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

AliZ PA-CF @base

Inherited from this (1)

AliZ PA-CF @System

Settings

Basic information

Material variant: PA-CF overridden
was PA (inherited)
Vendor: Aliz overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 inherited
Cost (/kg): 49.9 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 290 overridden
was 290 (inherited)
Nozzle (other layers) (°C): 290 overridden
was 290 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 0 (inherited)
Fan maximum (%): 30 overridden
was 60 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 overridden
was 4 (inherited)
Slow down if layer below (sec): 2 overridden
was 2 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 8 overridden
was 8 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	80 overridden was 100	80 overridden was 100
High Temp Plate	100 inherited	100 inherited
Textured PEI Plate	60 inherited	60 inherited
Cool Plate SuperTack	45 inherited	45 inherited

Other settings

activate air filtration: 0 inherited
chamber temperatures: 0 inherited
complete print exhaust fan speed: 80 overridden
was 70 (inherited)
during print exhaust fan speed: 60 overridden
was 70 (inherited)
enable pressure advance: 0 overridden
filament id: AliZ003 overridden
filament is support: 0 inherited
filament long retractions when cut: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil inherited
filament retraction minimum travel: nil inherited
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 2 overridden
was 0 (inherited)
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 300 overridden
was 300 (inherited)
nozzle temperature range low: 260 overridden
was 270 (inherited)
overhang fan speed: 40 overridden
was 30 (inherited)
overhang fan threshold: 0% overridden
was 95% (inherited)
pressure advance: 0.026 overridden
reduce fan stop start freq: 0 inherited
required nozzle HRC: 3 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 108 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "49.9"
  ],
  "filament_type": [
    "PA-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "80"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Aliz"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "290"
  ],
  "overhang_fan_speed": [
    "40"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "2"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "supertack_plate_temp": [
    "45"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "108"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "290"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "45"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "260"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "filament_id": "AliZ003",
  "pressure_advance": [
    "0.026"
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "name": "AliZ PA-CF @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:21