Generic PP @System
Generic · PP
· by phrozen-system
· 0 downloads
Inheritance
-
fdm_filament_common
→
fdm_filament_pp
→
Generic PP @System
Settings
Basic information
- Material variant
-
PP inherited
- Vendor
-
Generic inherited
- Diameter (mm)
-
1.75 inherited
- Density (g/cm³)
-
0.93 inherited
- Cost (/kg)
-
34.99 inherited
Print temperature
- Nozzle (initial layer) (°C)
-
235 inherited
- Nozzle (other layers) (°C)
-
235 inherited
Cooling
- Fan minimum (%)
-
100 inherited
- Fan maximum (%)
-
100 inherited
- Disable fan for first N layers
-
1 inherited
- Full fan if layer below (sec)
-
100 inherited
- Slow down if layer below (sec)
-
4 inherited
- Min speed when slowed (mm/s)
-
10 inherited
Flow
- Flow ratio
-
1 inherited
- Max volumetric speed (mm³/s)
-
12 inherited
Retraction
- Retraction length (mm)
-
nil inherited
- Retraction speed (mm/s)
-
nil inherited
- Deretraction speed (mm/s)
-
nil inherited
Bed temperature
| Plate | Initial layer (°C) | Other layers (°C) |
|---|---|---|
| Cool Plate |
35
inherited
|
35
inherited
|
| Engineering Plate |
0
inherited
|
0
inherited
|
| High Temp Plate |
55
inherited
|
55
inherited
|
| Textured PEI Plate |
55
inherited
|
55
inherited
|
| Cool Plate SuperTack |
0
inherited
|
0
inherited
|
Other settings
- activate air filtration
-
0 inherited
- additional cooling fan speed
-
70 inherited
- chamber temperatures
-
0 inherited
- complete print exhaust fan speed
-
70 inherited
- description
-
This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances. overridden
- during print exhaust fan speed
-
70 inherited
- filament id
-
OGFP97 inherited
- filament is support
-
0 inherited
- filament long retractions when cut
-
nil inherited
- filament minimal purge on wipe tower
-
15 inherited
- filament retract before wipe
-
nil inherited
- filament retract restart extra
-
nil inherited
- filament retract when changing layer
-
nil inherited
- filament retraction distances when cut
-
nil inherited
- filament retraction minimum travel
-
nil inherited
- filament scarf gap
-
0% inherited
- filament scarf height
-
10% inherited
- filament scarf length
-
10 inherited
- filament scarf seam type
-
none inherited
- filament shrink
-
100% inherited
- filament soluble
-
0 inherited
- filament wipe
-
nil inherited
- filament wipe distance
-
nil inherited
- filament z hop
-
nil inherited
- filament z hop types
-
nil inherited
- full fan speed layer
-
0 inherited
- instantiation
-
true overriddenwas false (inherited)
- nozzle temperature range high
-
250 inherited
- nozzle temperature range low
-
220 inherited
- overhang fan speed
-
100 inherited
- overhang fan threshold
-
50% inherited
- reduce fan stop start freq
-
1 inherited
- required nozzle HRC
-
3 inherited
- setting id
-
OGFSP97_00 overridden
- slow down for layer cooling
-
1 inherited
- temperature vitrification
-
110 inherited
Raw resolved JSON
{
"type": "filament",
"fan_max_speed": [
"100"
],
"fan_min_speed": [
"100"
],
"filament_cost": [
"34.99"
],
"filament_type": [
"PP"
],
"filament_wipe": [
"nil"
],
"instantiation": "true",
"eng_plate_temp": [
"0"
],
"filament_z_hop": [
"nil"
],
"hot_plate_temp": [
"55"
],
"cool_plate_temp": [
"35"
],
"filament_shrink": [
"100%"
],
"filament_vendor": [
"Generic"
],
"filament_density": [
"0.93"
],
"filament_soluble": [
"0"
],
"filament_diameter": [
"1.75"
],
"filament_end_gcode": [
"; filament end gcode\n"
],
"filament_scarf_gap": [
"0%"
],
"nozzle_temperature": [
"235"
],
"overhang_fan_speed": [
"100"
],
"compatible_printers": [],
"filament_flow_ratio": [
"1"
],
"filament_is_support": [
"0"
],
"required_nozzle_HRC": [
"3"
],
"slow_down_min_speed": [
"10"
],
"textured_plate_temp": [
"55"
],
"chamber_temperatures": [
"0"
],
"filament_settings_id": [
""
],
"filament_start_gcode": [
"; Filament gcode\n"
],
"filament_z_hop_types": [
"nil"
],
"full_fan_speed_layer": [
"0"
],
"slow_down_layer_time": [
"4"
],
"supertack_plate_temp": [
"0"
],
"filament_scarf_height": [
"10%"
],
"filament_scarf_length": [
"10"
],
"fan_cooling_layer_time": [
"100"
],
"filament_wipe_distance": [
"nil"
],
"overhang_fan_threshold": [
"50%"
],
"activate_air_filtration": [
"0"
],
"filament_scarf_seam_type": [
"none"
],
"filament_retraction_speed": [
"nil"
],
"temperature_vitrification": [
"110"
],
"filament_retraction_length": [
"nil"
],
"reduce_fan_stop_start_freq": [
"1"
],
"filament_deretraction_speed": [
"nil"
],
"slow_down_for_layer_cooling": [
"1"
],
"close_fan_the_first_x_layers": [
"1"
],
"eng_plate_temp_initial_layer": [
"0"
],
"filament_retract_before_wipe": [
"nil"
],
"hot_plate_temp_initial_layer": [
"55"
],
"cool_plate_temp_initial_layer": [
"35"
],
"filament_max_volumetric_speed": [
"12"
],
"during_print_exhaust_fan_speed": [
"70"
],
"filament_retract_restart_extra": [
"nil"
],
"complete_print_exhaust_fan_speed": [
"70"
],
"nozzle_temperature_initial_layer": [
"235"
],
"textured_plate_temp_initial_layer": [
"55"
],
"filament_long_retractions_when_cut": [
"nil"
],
"filament_retraction_minimum_travel": [
"nil"
],
"supertack_plate_temp_initial_layer": [
"0"
],
"filament_minimal_purge_on_wipe_tower": [
"15"
],
"filament_retract_when_changing_layer": [
"nil"
],
"filament_retraction_distances_when_cut": [
"nil"
],
"filament_id": "OGFP97",
"additional_cooling_fan_speed": [
"70"
],
"nozzle_temperature_range_low": [
"220"
],
"nozzle_temperature_range_high": [
"250"
],
"setting_id": "OGFSP97_00",
"description": "This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.",
"name": "Generic PP @System"
}
Version history
View full history with diffs →- v1 created 2026-05-19 13:21