fdm_filament_pps

Generic · PPS · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pps

Inherited from this (1)

Bambu PPS-CF @base

Settings

Basic information

Material variant: PPS overridden
was PLA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.36 overridden
was 0 (inherited)
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 320 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 320 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 0 overridden
was 35 (inherited)
Fan maximum (%): 50 overridden
was 100 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 overridden
was 60 (inherited)
Slow down if layer below (sec): 2 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.96 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 4 overridden
was 0 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Engineering Plate	110 overridden was 60	110 overridden was 60
High Temp Plate	110 overridden was 60	110 overridden was 60
Textured PEI Plate	110 overridden was 60	110 overridden was 60
Cool Plate SuperTack	0 overridden was 45	0 overridden was 45

Other settings

activate air filtration: 0 inherited
chamber temperatures: 60 overridden
was 0 (inherited)
complete print exhaust fan speed: 70 inherited
during print exhaust fan speed: 70 inherited
filament is support: 0 inherited
filament long retractions when cut: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil inherited
filament retraction minimum travel: nil inherited
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 340 overridden
nozzle temperature range low: 300 overridden
overhang fan speed: 30 overridden
was 100 (inherited)
overhang fan threshold: 0% overridden
was 95% (inherited)
reduce fan stop start freq: 0 inherited
required nozzle HRC: 3 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 125 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PPS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "110"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.36"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "320"
  ],
  "overhang_fan_speed": [
    "30"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "0.96"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "110"
  ],
  "chamber_temperatures": [
    "60"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "125"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "110"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "110"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "4"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "320"
  ],
  "textured_plate_temp_initial_layer": [
    "110"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "300"
  ],
  "nozzle_temperature_range_high": [
    "340"
  ],
  "name": "fdm_filament_pps"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:21