Phrozen PETG Basic @Phrozen Arco 0.2 nozzle

Phrozen · PETG · 0.20mm nozzle · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Phrozen PETG Basic @base

→

Phrozen PETG Basic @Phrozen Arco 0.2 nozzle

Compatible printers (1)

Phrozen Arco 0.2 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Phrozen inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 inherited
Cost (/kg): 24.99 inherited

Print temperature

Nozzle (initial layer) (°C): 245 inherited
Nozzle (other layers) (°C): 255 inherited

Cooling

Fan minimum (%): 20 overridden
was 20 (inherited)
Fan maximum (%): 50 overridden
was 40 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 overridden
was 30 (inherited)
Slow down if layer below (sec): 12 overridden
was 12 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 1 overridden
was 14 (inherited)

Retraction

Retraction length (mm): 0 overridden
was 0.4 (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Textured Cool Plate	0 inherited	0 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	70 inherited	70 inherited
Textured PEI Plate	70 inherited	70 inherited
Cool Plate SuperTack	70 inherited	70 inherited

Other settings

activate air filtration: 0 inherited
additional cooling fan speed: 0 inherited
chamber temperatures: 0 inherited
compatible printers: Phrozen Arco 0.2 nozzle overridden
was Phrozen Arco 0.2 nozzle, Phrozen Arco 0.4 nozzle, Phrozen Arco 0.6 nozzle (inherited)
complete print exhaust fan speed: 70 inherited
during print exhaust fan speed: 70 inherited
enable overhang bridge fan: 1 inherited
filament id: PRZB01 inherited
filament is support: 0 inherited
filament long retractions when cut: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil inherited
filament retraction minimum travel: nil inherited
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
idle temperature: 0 inherited
instantiation: true overridden
was false (inherited)
is custom defined: 0 inherited
nozzle temperature range high: 270 inherited
nozzle temperature range low: 230 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 25% overridden
was 10% (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: PRZB001_ARCO_A overridden
slow down for layer cooling: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited
version: 0 inherited
z hop types: Spiral Lift inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Phrozen"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "compatible_printers": [
    "Phrozen Arco 0.2 nozzle"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    "Phrozen PETG Basic"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "supertack_plate_temp": [
    "70"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "70"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "filament_id": "PRZB01",
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "version": "0",
  "z_hop_types": [
    "Spiral Lift"
  ],
  "idle_temperature": [
    "0"
  ],
  "is_custom_defined": "0",
  "textured_cool_plate_temp": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "slow_down_for_layer_cooling ": [
    "1"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "0"
  ],
  "setting_id": "PRZB001_ARCO_A",
  "name": "Phrozen PETG Basic @Phrozen Arco 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:21