eSUN PETG @base

eSUN · PETG · by phrozen-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

eSUN PETG @base

Inherited from this (1)

eSUN PETG @System

Settings

Basic information

Material variant: PETG inherited
Vendor: eSUN overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 1.27 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 20 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 20 inherited
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.98 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 20 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	65 overridden was 80	65 overridden was 80
Textured PEI Plate	65 overridden was 80	65 overridden was 80
Cool Plate SuperTack	70 inherited	70 inherited

Other settings

activate air filtration: 0 inherited
chamber temperatures: 0 inherited
complete print exhaust fan speed: 70 inherited
during print exhaust fan speed: 70 inherited
filament id: ESN03 overridden
was OGFG99 (inherited)
filament is support: 0 inherited
filament long retractions when cut: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil inherited
filament retraction minimum travel: nil inherited
filament scarf gap: 0% inherited
filament scarf height: 10% inherited
filament scarf length: 10 inherited
filament scarf seam type: none inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 250 overridden
was 260 (inherited)
nozzle temperature range low: 230 overridden
was 220 (inherited)
overhang fan speed: 100 inherited
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 64 overridden
was 70 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "65"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "eSUN"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "filament_scarf_gap": [
    "0%"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "0.98"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "65"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "supertack_plate_temp": [
    "70"
  ],
  "filament_scarf_height": [
    "10%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "64"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "65"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "65"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "70"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "filament_id": "ESN03",
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "name": "eSUN PETG @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:21