Bambu ASA-Aero @BBL X1C

Bambu Lab · ASA-AERO · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Bambu ASA-Aero @base

→

Bambu ASA-Aero @BBL X1C

Compatible printers (12)

Bambu Lab P1S 0.4 nozzle
Bambu Lab P1S 0.6 nozzle
Bambu Lab P1S 0.8 nozzle
Bambu Lab X1 0.4 nozzle
Bambu Lab X1 0.6 nozzle
Bambu Lab X1 0.8 nozzle
Bambu Lab X1 Carbon 0.4 nozzle
Bambu Lab X1 Carbon 0.6 nozzle
Bambu Lab X1 Carbon 0.8 nozzle
Bambu Lab X1E 0.4 nozzle
Bambu Lab X1E 0.6 nozzle
Bambu Lab X1E 0.8 nozzle

Settings

Basic information

Material variant: ASA-Aero inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.99 inherited
Cost (/kg): 49.99 inherited

Print temperature

Nozzle (initial layer) (°C): 270 inherited
Nozzle (other layers) (°C): 270 inherited

Cooling

Fan minimum (%): 30 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 30 inherited

Flow

Flow ratio: 0.52 inherited
Max volumetric speed (mm³/s): 12 inherited

Retraction

Retraction length (mm): 1.5 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	105 inherited	105 inherited
Textured PEI Plate	105 inherited	105 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1 0.4 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle overridden
description: This filament is only used to print models with a low density usually, and some special parameters are required. To get better printing quality, please refer to this wiki: ASA Aero Printing Guide. inherited
filament id: OGFB02 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament scarf seam type: none inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: 5 inherited
filament z hop: nil inherited
filament z hop types: Normal Lift inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 50 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 0 inherited
setting id: GFSB02_00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "49.99"
  ],
  "filament_type": [
    "ASA-Aero"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "0.99"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "50"
  ],
  "filament_flow_ratio": [
    "0.52"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "Normal Lift"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "5"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "1.5"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "This filament is only used to print models with a low density usually, and some special parameters are required. To get better printing quality, please refer to this wiki: ASA Aero Printing Guide.",
  "filament_id": "OGFB02",
  "filament_scarf_seam_type": [
    "none"
  ],
  "setting_id": "GFSB02_00",
  "compatible_printers": [
    "Bambu Lab P1S 0.4 nozzle",
    "Bambu Lab P1S 0.6 nozzle",
    "Bambu Lab P1S 0.8 nozzle",
    "Bambu Lab X1 0.4 nozzle",
    "Bambu Lab X1 0.6 nozzle",
    "Bambu Lab X1 0.8 nozzle",
    "Bambu Lab X1 Carbon 0.4 nozzle",
    "Bambu Lab X1 Carbon 0.6 nozzle",
    "Bambu Lab X1 Carbon 0.8 nozzle",
    "Bambu Lab X1E 0.4 nozzle",
    "Bambu Lab X1E 0.6 nozzle",
    "Bambu Lab X1E 0.8 nozzle"
  ],
  "name": "Bambu ASA-Aero @BBL X1C"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:11