Bambu ASA-Aero @base

Bambu Lab · ASA-AERO · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Bambu ASA-Aero @base

Inherited from this (4)

Settings

Basic information

Material variant: ASA-Aero overridden
was ASA (inherited)
Vendor: Bambu Lab overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.99 overridden
was 1.24 (inherited)
Cost (/kg): 49.99 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 270 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 250 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 10 (inherited)
Fan maximum (%): 50 overridden
was 60 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 overridden
was 35 (inherited)
Slow down if layer below (sec): 5 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 30 inherited

Flow

Flow ratio: 0.52 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 20 (inherited)

Retraction

Retraction length (mm): 1.5 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	105 inherited	105 inherited
Textured PEI Plate	105 inherited	105 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
description: This filament is only used to print models with a low density usually, and some special parameters are required. To get better printing quality, please refer to this wiki: ASA Aero Printing Guide. overridden
filament id: OGFB02 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament scarf seam type: none overridden
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: 5 overridden
was nil (inherited)
filament z hop: nil inherited
filament z hop types: Normal Lift overridden
was nil (inherited)
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 50 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 0 overridden
was 1 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "49.99"
  ],
  "filament_type": [
    "ASA-Aero"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "0.99"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "50"
  ],
  "filament_flow_ratio": [
    "0.52"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "Normal Lift"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "5"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "1.5"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "This filament is only used to print models with a low density usually, and some special parameters are required. To get better printing quality, please refer to this wiki: ASA Aero Printing Guide.",
  "filament_id": "OGFB02",
  "filament_scarf_seam_type": [
    "none"
  ],
  "name": "Bambu ASA-Aero @base"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 13:02
v1 created 2026-05-19 12:54