Prusa Generic TPU @CORE One 0.8

Generic · FLEX · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_flex

→

Prusa Generic TPU @CORE One

→

Prusa Generic TPU @CORE One 0.8

Compatible printers (2)

Prusa CORE One 0.8 nozzle
Prusa CORE One HF 0.8 nozzle

Settings

Basic information

Material variant: FLEX inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 inherited
Cost (/kg): 82 inherited

Print temperature

Nozzle (initial layer) (°C): 230 inherited
Nozzle (other layers) (°C): 230 inherited
Chamber (°C): 30 inherited

Cooling

Fan minimum (%): 30 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 10 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.08 inherited
Max volumetric speed (mm³/s): 7.5 overridden
was 2.5 (inherited)

Retraction

Retraction length (mm): 2.5 inherited
Retraction speed (mm/s): 60 inherited
Deretraction speed (mm/s): 20 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	60 inherited	60 inherited

Custom G-code

filament_start_gcode inherited

M900 K0 ; Filament gcode

M142 S36 ; set heatbreak target temp

Other settings

additional cooling fan speed: 70 inherited
bed type: Cool Plate inherited
compatible printers: Prusa CORE One 0.8 nozzle, Prusa CORE One HF 0.8 nozzle overridden
was Prusa CORE One 0.25 nozzle, Prusa CORE One 0.3 nozzle, Prusa CORE One 0.4 nozzle, Prusa CORE One 0.5 nozzle, Prusa CORE One HF 0.4 nozzle, Prusa CORE One HF 0.5 nozzle (inherited)
filament id: Prusa Generic TPU @CORE One 0.8 overridden
was Prusa Generic TPU @CORE One (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: 2 inherited
filament soluble: 0 inherited
filament wipe: 0 inherited
filament wipe distance: nil inherited
filament z hop: 0.6 overridden
was 0 (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
idle temperature: 150 inherited
instantiation: true overridden
was true (inherited)
overhang fan speed: 70 inherited
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "82"
  ],
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": [
    "0"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "0.6"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "overhang_fan_speed": [
    "70"
  ],
  "filament_flow_ratio": [
    "1.08"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "60"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "2.5"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "20"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "7.5"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_id": "Prusa Generic TPU @CORE One 0.8",
  "idle_temperature": [
    "150"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "setting_id": "GFSA04",
  "filament_notes": [
    ""
  ],
  "chamber_temperature": [
    "30"
  ],
  "compatible_printers": [
    "Prusa CORE One 0.8 nozzle",
    "Prusa CORE One HF 0.8 nozzle"
  ],
  "name": "Prusa Generic TPU @CORE One 0.8"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:46