Prusa Generic TPU @CORE One

Generic · FLEX · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_flex

→

Prusa Generic TPU @CORE One

Compatible printers (6)

Prusa CORE One 0.25 nozzle
Prusa CORE One 0.3 nozzle
Prusa CORE One 0.4 nozzle
Prusa CORE One 0.5 nozzle
Prusa CORE One HF 0.4 nozzle
Prusa CORE One HF 0.5 nozzle

Inherited from this (2)

Settings

Basic information

Material variant: FLEX overridden
was FLEX (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.22 overridden
was 1.22 (inherited)
Cost (/kg): 82 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 230 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 230 (inherited)
Chamber (°C): 30 overridden

Cooling

Fan minimum (%): 30 overridden
was 30 (inherited)
Fan maximum (%): 50 overridden
was 30 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 100 overridden
was 100 (inherited)
Slow down if layer below (sec): 10 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 10 (inherited)

Flow

Flow ratio: 1.08 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 2.5 overridden
was 2.5 (inherited)

Retraction

Retraction length (mm): 2.5 overridden
was 2.5 (inherited)
Retraction speed (mm/s): 60 overridden
was 60 (inherited)
Deretraction speed (mm/s): 20 overridden
was 20 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	50 overridden was 50	50 overridden was 50
Textured PEI Plate	60 inherited	60 inherited

Custom G-code

filament_start_gcode overridden

M900 K0 ; Filament gcode

M142 S36 ; set heatbreak target temp

Other settings

additional cooling fan speed: 70 inherited
bed type: Cool Plate inherited
compatible printers: Prusa CORE One 0.25 nozzle, Prusa CORE One 0.3 nozzle, Prusa CORE One 0.4 nozzle, Prusa CORE One 0.5 nozzle, Prusa CORE One HF 0.4 nozzle, Prusa CORE One HF 0.5 nozzle overridden
filament id: Prusa Generic TPU @CORE One overridden
was GFU99 (inherited)
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: 2 overridden
was 2 (inherited)
filament soluble: 0 overridden
was 0 (inherited)
filament wipe: 0 overridden
was 0 (inherited)
filament wipe distance: nil inherited
filament z hop: 0 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
idle temperature: 150 overridden
was 70 (inherited)
instantiation: true overridden
was false (inherited)
overhang fan speed: 70 overridden
was 80 (inherited)
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 overridden
was 1 (inherited)
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "82"
  ],
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": [
    "0"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "0"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "overhang_fan_speed": [
    "70"
  ],
  "filament_flow_ratio": [
    "1.08"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "60"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "2.5"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "20"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "2.5"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_id": "Prusa Generic TPU @CORE One",
  "idle_temperature": [
    "150"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "setting_id": "GFSA04",
  "filament_notes": [
    ""
  ],
  "chamber_temperature": [
    "30"
  ],
  "compatible_printers": [
    "Prusa CORE One 0.25 nozzle",
    "Prusa CORE One 0.3 nozzle",
    "Prusa CORE One 0.4 nozzle",
    "Prusa CORE One 0.5 nozzle",
    "Prusa CORE One HF 0.4 nozzle",
    "Prusa CORE One HF 0.5 nozzle"
  ],
  "name": "Prusa Generic TPU @CORE One"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:46